Publicidad
Idiomas disponibles
Idiomas disponibles
MOTOR
The sander is assembled with motor and wiring
installed as an integral part of the tool. The electrical
wiring schematic is shown in Figure 6.
The permanently split capacitor motor has the following
specifications:
Horsepower (Continuous Duty) ..................
1/3
Voltage ...................................
120
Amps .....................................
3.5
Hertz .....................................
60
Phase ..................................
Single
RPM ....................................
3500
Rotation (viewed from left side) ...........
Clockwise
ELECTRICAL
CONNECTIONS
WARNING:
All electrical connections must be per-
formed by a qualified electrician. Make sure tool is off
and disconnected from power source while motor is
mounted, connected, reconnected or anytime wiring is
inspected.
Motor and wires are installed as shown in wiring dia-
gram (See Figure 6). Motor is assembled with
approved, 3-conductor cord to be used at 120 volts.
Motor is prewired at the factory for 120 volts.
The power lines are inserted directly onto the switch.
The green ground line must remain securely fastened
to the frame to properly protect against electrical shock.
The power supply to the motor is controlled by a single
0ole locking rocker switch.
Switch
_
Motor
Figure 6 - Wiring Schematic
•
Remove the key to prevent unauthorized use.
Refer to Figures 7-15.
DESCRIPTION
Craftsman 2 x 6" Belt and Disc Sander has a 2" x 42"
belt and 6" disc for deburring, beveling and sanding
wood, plastic and metal. The sander has a fan-cooled 1/3
HP continuous duty motor. Belt speed is 4400 FPM and
the disc rotates 3500 RPM. The belt table tilts 0 to 90 °
and the disc table tilts 0 to 45 ° for angle sanding. The
quick release tension and tracking mechanism makes
belt changing quick and easy. Belt platen is removable
for contour sanding. Belt housing swivels from vertical
to horizontal for sanding large workpieces. Disc guard
has 11/2"dust collection chute.
SPECIFICATIONS
Belt size ..........................
2 x 42"_ 80 grit
Belt platen area .........................
2 x 71/4 ' '
Belt table dimensions .....................
9 x 63A''
Belt table tilts ...........................
0 to 90 °
Belt speed ...........................
4400 FPM
Disc diameter ...............................
6"
Disc table dimensions
..................
83/16 x 57/1_ ''
Disc table tilts ...........................
0 to 45 °
Disc dust chute diameter .....................
lV2"
Disc speed ..........................
3500 RPM
Base dimensions ......................
91/16x 8%2"
Switch ........................
SE Locking rocker
Weight ................................
30.2 Ibs
WARNING:
Operation of any power tool can result in
foreign objects being thrown into the eyes, which can
result in severe eye damage. Always wear safety gog-
gles complying with United States ANSI Z87.1 (shown
on package) before commencing power tool operation.
Safety goggles are available at Sears retail stores or
catalog.
CAUTION:
Always observe following safety precautions.
SAFETY
PRECAUTIONS
•
Whenever adjusting or replacing any parts on the
tool, turn switch OFF and remove the plug from
power source.
•
Recheck table knobs. They must be tightened
securely.
•
Make sure all guards are properly attached. All
guards should be securely fastened.
•
Make sure all moving parts are free and clear of any
interference.
•
Make sure all fasteners are tight and have not
vibrated loose.
•
With power disconnected, test operation by hand for
clearance and adjust if necessary.
•
Always wear eye protection or face shield.
•
Make sure abrasive belt always tracks properly.
Correct tracking gives optimum performance.
•
After turning switch on, always allow belt to come up
to full speed before sanding or grinding.
•
Be sure motor runs clockwise on disc side. Abrasive
belt must travel down.
•
Avoid kickback by sanding in accordance with the
directional arrows.
•
Keep your hands clear of abrasive belt, disc and all
moving parts.
•
For optimum performance, do not stall motor or
reduce speed. Do not force the work into the abrasive.
•
Support workpiece with belt table when sanding with
belt, with disc table when sanding with disc.
•
Never push a sharp corner of the workpiece rapidly
against the belt or disc. Abrasive backing may tear.
Publicidad
