Publicidad
Idiomas disponibles
Idiomas disponibles
• Replace abrasives w hentheybecome loaded
(glazed) o r frayed.
• Whengrinding metal, m oveworkpiece a crossabra-
siveto prevent h eatbuiltup.
• Never a ttempt w etsanding. I f theworkpiece
becomes t oo hotto handle, c oolit in water.
WARNING: S ome dustcreated bypower sanding,
sawing, g rinding, drilling andotherconstruction a ctivi-
tiescontains chemicals k nown tocausecancer, b irth
defects or otherreproductive harm.
Someexamples o f thesechemicals a re:
• Leadfromlead-based p aints.
• Crystalline s ilicafrombricksandcement a ndother
masonry products.
• Arsenic a ndchromium fromchemically-treated
lumber.
Yourriskfromtheseexposures v ary,depending o n how
oftenyoudothistypeofwork. T oreduce yourexposure
tothesechemicals: workin a wellventilated areaand
workwithapproved s afetyequipment. Always wear
OSHA/NIOSH a pproved, properly f ittingfacemaskor
respirator whenusingsuchtools.
MOUNT SANDER
During operation the sander may have a tendency to slide
or move about on the bench or table. It is recommended
to mount the sander onto a stand (see "Recommended
Accessories", page 13) or to a bench top.
ADJUSTING
BELT TABLE
Refer to Figure 7.
WARNING:
Disconnect sander from power source
before making any adjustments.
•
To adjust belt table angle, loosen the socket head
bolt and adjust table to desired angle. Use a combi-
nation square to set belt table at 45 ° or 90 ° from belt
platen.
•
Adjust for 1/16" m aximum clearance between the belt
and the table.
•
Secure table position by tightening bolt.
S°CkdeBolt /__BeltCover
"_r--- Belt Platen
/..._Bracket
Socket Head
Bolt
_K. - _
Belt Table
_'Socket
Head Bolt
Figure 7 - Adjustments
REPLACING
ABRASIVE
BELT
Refer to Figures 7 and 8.
WARNING:
Disconnect sander from power source
before making any adjustments.
•
Sanding belt should be replaced when worn, torn, or
glazed.
•
Loosen and remove two knobs from belt cover.
•
Remove belt cover.
•
Loosen and remove socket head bolt from bracket.
•
Remove bracket.
•
Loosen socket head bolt and move belt table parallel
to belt.
•
Release belt tension by pulling down on handle
assembly. Slide old belt off the drive and tracking
wheels.
NOTE: There may be an arrow on the inside of the belt.
The arrow should point in the direction of belt travel to
ensure that the splice in the belt will not come apart.
•
Pull down on the handle and slide new belt over the
drive and idler wheels. Center belt on wheels.
•
Rotate belt by hand to check tracking. Belt should
ride centered on wheels.
•
If belt does not ride centered on wheels, adjust belt
tracking as described in the next section.
•
Replace belt cover and secure it with two knobs.
•
Replace bracket and secure it with socket head bolt.
•
Reset belt table to be at the desired angle, and
secure it by tightening the bolt.
Idler Wheel
Handle
Belt
Drive Wheel
Figure 8 - Replace Abrasive Belt
TRACKING
ABRASIVE
BELT
Refer to Figure 9, page 7.
•
Test the tracking. Plug in power cord. Turn switch ON
and immediately OFF. If the abrasive belt is centered
on wheels and did not move to the right or left, it is
tracking properly. If the belt moved to the right or left,
adjustment is necessary.
•
To adjust the tracking wheel, loosen the locking nut
on adjusting bolt. Use a 4mm hex wrench to turn
adjusting bolt.
6
Publicidad
