HIKOKI NT 65GS Instrucciones De Manejo página 9

g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations diff erent from
those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specifi ed by
the manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fi re when used with
another battery pack.
b) Use power tools
designated battery packs.
Use of any other battery packs may create a risk of
injury and fi re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, fl ush with water. If
liquid contacts eyes, additionally seek medical
help.
Liquid ejected from the battery may cause irritation
or burns.
e) Do not use a battery pack or tool that is
damaged or modifi ed.
Damaged or modifi ed batteries may exhibit
unpredictable behaviour resulting in fi re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to fi re or
excessive temperature.
Exposure to fi re or temperature above 130°C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specifi ed in the instructions.
Charging improperly or at temperatures outside
the specifi ed range may damage the battery and
increase the risk of fi re.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
only with specifi cally
PRECAUTIONS ON USING GAS FINISH NAILER
1. Safe operation through correct usage.
This tool was designed for driving nails into wood and
similar materials. Use it for its intended purpose only.
2. Be careful of ignition and explosions.
This tool must not be used in a
combustible
presence
or gases. This tool produces hot
exhaust gases that may ignite
fl ammable materials and produces sparks. Since
sparks may fl y during nailing, it is dangerous to use
this tool near lacquer, paint, benzine, thinner, gasoline,
gas, adhesives and similar infl ammable substances as
they may ignite or explode. Under no circumstances
should this tool therefore be used in the vicinity of such
infl ammable material.
3. Explosion and fi re hazard.
The fuel cell is an aerosol dispensers
with fl ammable contents.
Pressured
propellant will remain in the fuel cell.
Failure to follow instructions may
result in explosion or fi re.
Keep the power tool, fuel cells and
MAX 50°C
battery away from sunshine and
(120°F)
from temperature exceeding 50°C
(120°F).
Fuel cell and/or battery may burst,
releasing fl ammable gas.
Do not pierce or burn the container,
even after use.
Do not incinerate, refi ll, reclaim or
recycle the fuel cell.
Do not spray to a naked fl ame or any
incandescent material.
Keep away from ignition sources – No smoking.
Keep out of the reach of children.
4. Always wear eye protection (protective goggles).
When operating the power tool,
always wear eye protection, and
ensure that surrounding people wear
eye protection too.
The possibility of fragments of the
nails that were not properly hit entering the eye is a
threat to sight. Eye protection can be bought at any
hardware store. Always wear eye protection while
operating this tool. Use either eye protection or a wide
vision mask over prescription glasses.
Employers should always enforce the use of eye
protection equipment.
5. Protect your ears and head.
When engaged in nailing work please
wear ear muffl ers and head protection.
Also, depending on condition, ensure
that surrounding people also wear ear
muffl ers and head protection.
Unprotected exposure to high noise levels can cause
permanent, disabling, hearing loss and other problems
such as tinnitus (ringing, buzzing, whistling or humming
in the ears).
Risk assessment and implementation of appropriate
controls for these hazards are essential.
Appropriate controls to reduce the risk may include
actions such as damping materials to prevent
workpieces from "ringing".
Operate and maintain the tool as recommended in
these instructions, to prevent an unnecessary increase
in noise levels.
English
environment or in
of fl ammable liquids
container and the
9