Before Use - HIKOKI NR 90GC2 Instrucciones De Manejo

English
○ Do not attempt to reuse the metering valve.
Replace with the new metering valve.
2. Battery
You must charge the battery before use.
The charging method of battery is shown in page 13.
3. Check on safety
CAUTION
○ Unauthorized persons (including children) must be kept
away from the equipment.
○ Wear eye protector.
○ Check the retaining screws which fi x the top cover, etc.
for tightness.
Check the tool for defective or rusty parts.
○ Check whether or not the push lever works correctly
without nails, fuel cell and battery. Also check whether
or not any dirt has adhered to the moving parts of the
push lever.
○ Recheck on operational safety.

BEFORE USE

1. Insert battery into the tool (See Fig. 4)
Do not operate the push lever or trigger while installing
the battery.
Make sure the battery indicator light is fl ashing GREEN
(See Fig. 5).
If the battery indicator light is fl ashing RED, the battery
doesn't have enough power and it needs to be charged.
BATTERY INDICATOR LIGHT
– Flashing GREEN: Enough
– Flashing RED: Insuffi cient power remaining (The
light turns steady during operation).
– OFF: The battery is extremely empty. Charge the
battery.
2. Insert fuel cell into the tool
(1) Pulling the latch and open the cell cover (See Fig. 6).
(2) Insert the fuel cell into the tool (See Fig. 7).
(3) Insert the stem of fuel cell into the hole of adaptor (See
Fig. 8).
(4) Close the cell cover.
3. Load nails
(1) Insert nail strip into rear of magazine (See Fig. 9).
(2) Slide the nail strip forward in the magazine (See
Fig. 10).
(3) Pull the nail feeder (B) back to engage the feeder knob
to the nail strip (See Fig. 11).
NOTE
Use nail strip of more than 10 nails.
The Nailer is now ready to operate.
Removing the nails:
1 Pull the feeder knob backward (See Fig. 12).
2 Return the feeder knob forward quietly while pushing
the nail feeder (B).
3 Pull out nails from the back of the magazine (See
Fig. 13).
CAUTION
To prevent unintentional operation, never touch the
trigger or place the top end of the push lever on a work
bench on fl oor. Also, never face the nail outlet toward
any part of a person.
14
power remaining
(The light turns steady during
operation).
HOW TO USE THE NAILER
CAUTION
○ Do not use the housing or any portion of the tool as a
hammer as nails may be discharged unexpectedly or
the tool may become damaged and serious injury could
occur.
○ Take precautions to ensure the safety of persons in the
vicinity during operation.
○ Squeeze the trigger when drive a nail, otherwise the
piston can not return correctly.
○ Make sure the nailing depth when the temperature is
above 40°C or below 0°C.
○ Ensure tool is always safely engaged on the workpiece
and cannot slip.
1. Nailing procedures
This power tool is equipped with a FULL SEQUENTIAL
ACTUATION MECHANISM.
(1) Intermittent nailing
Depress the nail outlet onto the desired point; then pull
the trigger to drive a nail in a single shot (See Fig. 15).
After nailing once, nailing will not be possible again until
the trigger is released and pressed again.
(2) Push lever
When depressing the nail outlet, be sure to fully lift
the push lever (See Fig. 15) to release the safety lock.
Thus, nails cannot be driven without releasing the
safety lock even though the trigger is pulled.
The machine employs a preventive mechanism for
unloaded operation.
The machine enters a state where the push lever cannot
be pushed up. This takes place when the magazine is
not loaded with nails or when the remaining number
of nails becomes less than 8 or 9 (NR90GC2), 5 or 6
(NR90GR2).
CAUTION
○ Exercise care when nailing corners of lumber. When
continuous nailing corners of lumber, a nail may go
astray or break through the corner.
○ Do not drive a nail on another nail.
○ Do not drive a nail on metal parts.
○ Use caution not to throw the push lever tip onto wood
when the push lever cannot be pushed up.
NOTE
Under low temperature conditions, the tool sometimes
does not operate correctly. Always operate the tool at
the appropriate ambient temperature.
2. Adjusting the nailing depth (See Fig. 17, 18)
To assure that each nail penetrates to the same depth,
be sure that the tool is always held fi rmly against the
workpiece.
If nails are driven too deep or shallow into the workpiece,
adjust the nailing in the following order.
1 Remove the fuel cell and the battery from the nailer
(See Fig. 16).
2 If nails are driven too deep, move the push lever to
forward (See Fig. 17).
If nails are driven too shallow, move the push lever
to backward (See Fig. 18).
3 Stop moving the push lever when a suitable position
is reached for a nailing test.
4 Connect the fuel cell and the battery to the nailer.
ALWAYS WEAR EYE PROTECTOR.
Perform a nailing test.
5 Remove the fuel cell and the battery from the nailer.
6 Choose a suitable position for the push lever.