Milwaukee K 2000 H Manual Original página 7

TECHNICAL DATA BREAKER HAMMER
Production code.......................................................................
Rated input ..............................................................................
Output ......................................................................................
Rate of percussion under load max. ........................................
Impact energy per stroke according to EPTA-Procedure 05/2009 ....
Tool reception ..........................................................................
Weight according EPTA-Procedure 01/2003 ..........................
Vibration information
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Chiselling:
Vibration emission value a ...................................................
h
Uncertainty K= .........................................................................
WARNING!
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given
in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent
applications, with diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase
the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR BREAKER HAMMER
Wear ear protectors. Exposure to noise can cause hearing
loss.
surfaces, when performing an operation where the cutting
accessory may contact hidden wiring. Cutting accessory
contacting a „live" wire may make exposed metal parts of
the power tool „live" and could give the operator an electric
shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust
protection mask.
Do not machine any materials that present a danger to
health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
12 ENGLISH
K2000H
..................... 4634 07 01...
...000001-999999
.......................2200 W
....................... 1100 W
.......................1300 min -1
...........................42 J
...........................28 mm
........................24,1 kg
..........................4,7 m/s2
..........................0,5 m/s2
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Keep mains lead clear from working range of the machine.
Always lead the cable away behind you.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Always disconnect the plug from the socket before carrying
out any work on the machine.
Always keep a safe footing and hold machine with both
hands. Keep children or animals away from working area.
Do not direct the machine towards people standing close
whilst it is operating. The inserted tool could be catapulted
out and cause serious injuries.
Ensure that nobody is at risk of materials being catapulted
out or falling. Always work carefully and attempt to anticipate
potential dangers.
Put down the machine carefully. Do not throw the machine
to the ground or drop it from great heights. If it is thrown to
the ground, the machine may injure others or suff er damage
itself.
SPECIFIED CONDITIONS OF USE
The hammer can be used for chiselling in stone and
concrete.
Do not use this product in any other way as stated for
normal use.
MAINS CONNECTION
Appliances used at many diff erent locations including wet
room and open air must be connected via a residual current
device (FI, RCD, PRCD) of 30mA or less.
Connect only to single-phase AC system voltage as
indicated on the rating plate. It is also possible to connect to
sockets without an earthing contact as the design conforms
to safety class II.
Make sure the machine is switched off before plugging in.
This is a device for professional use which may slightly
exceed the guide values for current harmonics when it is
connected to the public low voltage mains supply. You
should therefore contact your energy supply company
before you connect the device to the public low voltage
mains supply.
TRANSPORT, HANDLING AND STORAGE
The machine is heavy. It may cause serious injuries if it is
dropped.
The machine has no lifting or lashing points.
Lift the machine using the additional handle and place it on
a suitable means of transport.
Secure the machine whilst it is being lifted, transported or
stored to prevent it tipping over, falling or slipping.
Always allow the machine to cool down before placing it in
storage.
Store the machine in a locked, clean, dry place which is
protected from frost and inaccessible for children.
CHANGING THE TOOL
See the picture section for instructions on changing the tool.
The inserted tool must be suitable for the tool mounting.
The shaft of the inserted tool must be undamaged.
The inserted tool must be adequately sharp to prevent
recoil.
The inserted tool must be suitable for the planned work.
After inserting the tool, check whether it has been locked
correctly.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Grease the machine at the lubricating nipple every 20 h, ~
3 months of service (see picture section).
Important note! If the carbon brushes are worn, in addition
to exchanging the brushes the tool should be sent to
after-sales service. This will ensure long service life and top
performance.
If the supply cord of this appliance is damaged, it must only
be replaced by a repair shop appointed by the manufacturer,
to avoid hazardous situations.
Use only Milwaukee accessories and Milwaukee spare
parts. Should components need to be replaced which have
not been described, please contact one of our Milwaukee
service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the six-digit
No. on the label and order the drawing at your local service
agents or directly at: Techtronic Industries GmbH,
Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any
work on the machine.
Please read the instructions carefully before
starting the machine.
Wear gloves!
Wear ear protectors!
Always wear goggles when using the machine.
Caution – hot surfaces!
The guaranteed sound power level shown on this
label is 96 dB.
Do not dispose electric tools, batteries/
rechargeable batteries together with household
waste material.
Electric tools and batteries that have reached the
end of their life must be collected separately and
returned to an environmentally compatible
recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
National mark of conformity Ukraine
EurAsian Conformity Mark
ENGLISH 13