Craftsman professional INCREDI-PULL 316.794000 Manual Del Operador página 7

HOW TO START THE UNIT USING THE PLUG-IN POWER START OR POWER BIT
START ACCESSORY
NOTE- This unit can use a Plug-In Power Start or Power Bit Start optional
accessory!
Please refer to the Plug-in Power Start or Power Bit Start operator's manual
for proper use of this feature. (Items Sold Separately? Please refer to page 9
of this manual about purchasing these accessories.)
STARTING INSTRUCTIONS
1. Mix fuel with oil. See Oil and Fuel Mixing Instructions.
2. Fill the fuel tank with fresh fuel mix. Refer to Fueling the Unit.
NOTE: There is no need to turn the unit on. The On/Off Control is in the ON ( I )
position at all times (Fig. 9).
3. Slowly press and release the primer bulb 10 times. Some amount of fuel should
be visible in the primer bulb (Fig. 10). If fuel can not be seen in the bulb, press and
release the bulb until fuel is visible.
4. Move the choke lever to Position 1 (Fig. 10).
5. Press down the cruise control to lock the trigger into the FAST position (Fig. 9).
6. Crouch in the starting position (Fig. 11). Place the Plug-In Power Start or Power Bit
Start into the back of the unit. Refer to the Operation section of the Plug-In Power
Start or Power Bit Start operator's manual.
7. Press and hold the ON (I) button of the Plug-in Power Start or Power Bit Start
equipped drill for 2 seconds.
8. Move the choke lever to Position 2 (Fig. 10).
9. Press and hold the ON (I) button of the Plug-in Power Start or Power Bit Start
equipped drill in intervals no longer than 2 seconds each until the unit starts.
10. Remove the Plug-In Power Start or drill from the unit.
11. While continuing to keep the throttle trigger in the FAST position, allow the engine
to warm up for 30 to 60 seconds.
12. While continuing to keep the throttle trigger in the FAST position, move the choke
lever to Position 3 and continue warming the unit for an additional 60 seconds
(Fig. 10). The unit may be used during this time.
NOTE: The cruise control may be released and the throttle control used normally
once the engine has been properly warmed.
NOTE: The unit is properly warmed up when the engine accelerates without hesitation.
IF... the engine hesitates, return the choke lever to Position 2 (Fig. 10) and continue
the warm-up.
IF... the engine does not start, go back to step 3.
IF... the engine fails to start after two attempts, move the choke lever to Position 3
(Fig. 10) and press down the cruise control. Then press and hold the Plug-in
Power Start or drill ON (I) button in intervals no longer than 2 seconds each
until the unit starts.
IF WARM... If the engine is already warm, start the unit with the choke lever in Position 2
(Fig. 10). After the unit starts, move the choke lever to Position 3 (Fig. 10).
Using the Cruise Control
1. Once the engine has started and warmed up, squeeze the trigger to accelerate
the unit as needed (Fig. 9).
2. For longer periods of operation and to eliminate possible finger fatigue, move the
cruise control toward the FAST position to incrementally increase or maintain the
unit's engine speed (Fig. 9). When the cruise control is pressed, the trigger will
recede into the handle.
3. To decrease engine speed, move the cruise control to the SLOW position and the
trigger will return to idle position (Fig. 9).
STOPPING INSTRUCTIONS
1. Release the trigger or move the cruise control to the SLOW position and allow the
engine to cool down by idling.
2. Press and hold the On/Off Control switch in the OFF (O) position until the engine
comes to a complete stop (Fig. 9).
PUTTING ON THE UNIT
1. Place the shoulder supports over
the shoulders so that the engine
rests on the operator's back.
2. Pull the shoulder support straps
down to tighten the shoulder
supports (Fig. 12).
NOTE: The unit must be started
prior to putting it on. See
Starting/Stopping
Instructions.
TAKING OFF THE UNIT
1. Pull up on the bottom tabs of the
shoulder support buckles to
loosen the shoulder supports
(Fig. 13).
2. Remove the unit.
HOLDING THE BLOWER
Shoulder
Support
Straps
Shoulder
Supports
Fig, 12
Shoulder
Support
Buckles
Fig, 13
I_ I WARNING:
To avoid serious personal injury, wear eye and hearing
I
protection at all times when operating this unit. Wear a dust mask in dusty
locations.
Before operating the unit, stand in the
operating position (Fig. 14). Check for
the following: I
• The operator is wearing eye and
hearing protection.
• The operator is wearing proper
clothing.
• If the conditions are dusty, the
operator is wearing a dust mask.
• The unit is secure and comfortable
on the operator's back.
• The right arm is bent and the right
hand is gripping the throttle grip.
L.
Fig. 14
OPERATING TIPS
I_ I WARNING:
To prevent serious personal injury or damage to the unit,
I
make sure the blower tubes are in place before operating the unit.
• Never direct the unit at anyone while the unit is in operation.
• Always hold the unit securely when operating.
• To reduce the risk of hearing loss associated with sound level(s), hearing protection
is required.
• Operate power equipment only at reasonable hours-- not early in the morning or late
at night when people might be disturbed. Comply with times listed in local ordinances.
Usual recommendations are 9:00 am to 5:00 pm, Monday through Saturday.
• To reduce noise levels, operate power blowers at the lowest possible speed to de the
job and limit the total number of pieces of power equipment used at any one time.
• Check your equipment before operation, especially the muffler, air intakes and air filters.
• Use rakes and brooms to loosen debris before blowing.
• In dusty conditions, slightly dampen surfaces.
• Conserve water by using power blowers instead of hoses for many lawn and garden
applications, including cleaning debris from areas such as screens, patios, grills,
porches, and gardens.
• Watch out for children, pets, open windows or freshly washed cars, and blow debris
safely away.
• Use the full blower nozzle extension so the air stream can work closer to the ground.
• Clean up after using blowers and other equipment. Dispose of debris appropriately.
• Use the cruise control (Fig. 9) to keep the trigger depressed while operating to make
continuous operation easier.
APPLICATIONS
1 Use the blower for trees, shrubs, flower beds and hard-to-clean areas.
2. Use the unit around buildings and for other normal cleaning procedures.
3. Use the blower around walls, overhangs, fences and screens.