Publicidad
Idiomas disponibles
Idiomas disponibles
Connecting
and Disconnecting
the Portable/
Convertible
Dishwasher
The portable/convertible
dishwasher
must be connected
to a faucet
and electrical
outlet each time it is used.
Follow directions
on this page to properly
connect
dishwasher.
Faucet
Adapter
Assembly
(Figure
A)
For Inside
Threaded
Threaded
Faucet
Faucet
Use
Use
and
Washer
Thin
Only
Washers
Ada
Two Brass
(Dual
Screens
Thread)
should
be
below
the
rubber
washers
Connecting
the
Portable
Faucet
Adapter
Assembly
(Figure
B)
IMPORTANT:
Make sure door
is latched
before
moving
dishwasher.
The power cord, faucet
coupler
and hoses are located
in a compartment
in
back of dishwasher.
A special
adapter
must be installed
on faucet
before you
can connect
dishwasher
(Figure A).
1. Remove
faucet
adapter
assembly
from literature
package.
2. Unscrew
existing
sink faucet
aerator.
3. Check faucet
spout to see if threads
are inside or outside.
• If threads
are on inside of faucet spout,
use both thick and thin rubber
washers.
• If threads
are on outside of faucet spout,
use thin rubber washer
only.
• If faucet
has no threads,
an adapter
kit with instructions for attachment
to
a non-threaded
spout is available
at most hardware
stores.
4. Assemble
faucet
spout as shown in Figure A. Make sure the two brass
screens
are located
below the rubber washers.
Connecting
the PortablelConvertible
Dishwasher
1. Run water at faucet until it is hot. Turn off faucet.
2.
Pull hoses out of compartment.
3. Push collar down and slip faucet
connector
onto faucet
adapter
(Figure
B).
4. When connector
snaps into place, release
collar.
5. Slowly turn on hot water all the way.
6. Plug power cord into grounded
outlet.
Electric
Shock
Hazard
Avoid
fire hazard
or
electrical
shock.
Do
not use an adapter
plug, extension
cord
or
remove
grounding
prong from
electrical
power
cord.
Failure
to
follow
this warning
can
cause
serious
injury,
fire or death.
Grounding
type
wall
receptacle
Do not under
any
circumstances
cut,
remove
or bypass
the grounding
prong
from
this
plug.
Disconnecting
the PortablelConvertible
Dishwasher
1. When cycle has finished,
turn off hot water.
2.
Press red button on coupler
to release
water pressure.
3. Press down on collar to release
coupler•
4.
Empty remaining
water from coupler
and return it to compartment.
5. Unplug power cord and return it to compartment.
IMPORTANT:
A sink spray hose can burst
due to constant
water
pressure
while
in use. If your spray hose is installed
on same water
line
as the dishwasher,
it is your responsibility
to disconnect
sink's
spray
hose and to plug hole.
Electrical
Connection
for a PortablelConvertible
Dishwasher
An electrical
supply of 120 volts, 60 Hz, AC only, 15 amps is required.
For
your safety,
the dishwasher
must be grounded•
If there is a malfunction
or
breakdown,
grounding
will reduce
risk of electrical
shock. This dishwasher
has a power cord with a 3-prong
grounding
plug. It must be plugged
into a
mating 3-prong
grounding
type receptacle,
installed
and grounded
in
accordance
with the National
Electrical
Code and any local codes and
ordinances.
To Convert
a Portable
Model
to a Built-in
Your portable
dishwasher
can be installed
under the counter.
A conversion
kit
_s required
and is available
at your Sears Service
Center - Part No.
154400101.
Power
supply
cord
with
3-prong
grounding
plug.
IMPORTANT:
Do not use the portable
water
supply
hose
for permanent
installation.
It may burst. Complete
instructions
are in the conversion
kit.
12
Publicidad
