Fluval Aquarium Led: Parts; Important Safety Instructions - Fluval Roma Manual De Instrucciones

READ THOROUGHLY PRIOR TO INSTALLATION
AND OPERATION

FLUVAL AQUARIUM LED: PARTS

A) 1 x TOP FRAME attached to the aquarium
B) CANOPY
• 2 x LIDS for opening and closing the aquarium (B1); 3 x LIDS for Venezia 350
• 1 x black aluminium beam (B2); 2 x Black Aluminium beam for Venezia 350
C) 1 x LED Strip Light; 2 x LED Strip Light for Venezia 350
D) GLASS TANK
B2
C
Roma series
D
B2
C
D
Venezia 190

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To guard against injury, basic safety precautions should be observed when handling the LED Strip
Light, including the following:
1. For the complete enjoyment, use and understanding of this product,
ALL SAFETY INSTRUCTIONS
ing. Failure to do so may result in loss of life and/or injury or damage to the unit.
2. DANGER – To avoid possible electrical shock, special care should be taken due to the close proximity of
the LED Strip Light to water. For each of the following situations, do not attempt repairs yourself; return the
appliance to an authorized service facility for service or discard the appliance. (See Customer Service
information at the end of this manual).
If the unit falls into the water, DON'T reach for it! First unplug it and then retrieve it. If the electrical
components of the appliance get wet, unplug the appliance immediately.
4
B2
B1
C
A
Vicenza 180 and 260
D
B2
B1
C
A
D
Venezia 350
READ AND FOLLOW
and all important notices on the appliance before us-
Carefully examine the appliance after installation. It should not be plugged in if there is water on parts
not intended to be wet.
Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or if it is dropped
or damaged in any manner. The power cord of this appliance cannot be replaced; if the cord is damaged,
the appliance should be discarded. Never cut the cord.
To avoid the possibility of the appliance plug, switch or wall socket getting wet,
position the unit to one side of a wall mounted wall socket to prevent water from
dripping onto the socket or plug. A "drip loop" (see illustration) should be arranged
to the socket. The "drip loop" is that part of the cord below the level of the socket
(or the connector if an extension cord is used), to prevent water travelling along the
cord and coming into contact with the wall socket. If the plug or socket does get wet,
DON'T unplug the cord. Disconnect the fuse or circuit breaker that supplies power
to the appliance. Then unplug and examine for presence of water in the wall socket.
3. Close supervision is necessary when any appliance is used by or near children. This appliance can be used
by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities
B1
or lack of experience and knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision. This product is not a toy.
4. To avoid injury, do not come into contact with moving parts or hot parts such as heaters, LED device, etc.
5. CAUTION – Always unplug or disconnect all appliances in the aquarium from electricity supply before
A
placing hands in water, before putting on or taking off parts and whilst this LED Strip Light is being installed,
maintained or handled. Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.
Always unplug an appliance from an outlet when not in use.
WARNING: The line cord Switch on the LED Strip Light cannot be considered a safety switch.
6. Do not use an appliance for other than intended use (i.e. don't use on swimming pools, garden ponds,
bathrooms, etc.). The use of attachments not recommended or sold by the appliance manufacturer may
result in a dangerous situation. Do not try to repair any product component: in case of damage replace the
B1
damaged component with original spare parts.
7. IMPORTANT: This LED Strip Light is a non-submersible AQUARIUM LUMINAIRE suitable FOR INDOOR
USE ONLY designed to be assembled onto FLUVAL Roma, Vicenza and Venezia Top Cover Frames only.
For fresh and salt water ornamental aquariums with max 35 °C water temperature. Do not install or store the
A
appliance anywhere where temperatures may drop below freezing.
8. IMPORTANT: Make sure that the LED Strip Light is securely and correctly installed before operating it
and that the minimum distance of water from the LED Strip Light is 15 mm. This LED Strip Light must never
operate in water.
Fill the aquarium up
situated on the inside
IMPORTANT: Do not over fill. Overfilling the aquarium can
cause water to pass under the top frame which then runs down
the outside of the aquarium.
WARNING: Do not plug in the LED Strip Light if there is water on parts not intended to be wet.
WARNING: Do not place any object(s) on the LED Strip Light (C) or on the Canopy (B). Ensure sufficient
air space around the LED Strip Light. The safety of this appliance is only ensured provided that it has
been properly installed.
9. Read and observe all the important notices on the appliance.
10. If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes
or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not
be tripped over or pulled.
11. SAVE THESE INSTRUCTIONS
to level indicated on the label
of the aquarium's top frame.
DRIP LOOP
5