Publicidad
Idiomas disponibles
Idiomas disponibles
ProbJem
Diagnosis
Remedy
The machine does not work when switched
1. No power supply.
1. Check the cable for breakage.
on.
2. Defective switch.
2. Replace the lock switch.
3 Defective motor.
3. Defective motor.
The saw blade does not move with the
motor running.
The saw blade does not cut in a straight
line.
1. The blade tension knob has not been
tightened.
2. The blade has come off one d the
wheels.
3. The saw blade has broken.
4. The drive belt has snapped.
1. Rip fence for cutting not used.
2. Feed rate too fast.
3. The blade teeth are dull or damaged.
4. Blade guides not suitably adjusted.
1. Switch off the motor, tighten the blade
tension knob.
2. Open the doors and check.
3. Replace the blade.
4. Replace the belt.
1. Use a rip fence.
2. Put light pressure on the work piece.
Make sure the saw blade does not bend.
3. Try a new saw blade.
4. Adjust the blade guides (see ADJUST-
MENT instructions).
The saw blade does not cut, or cuts very
slowly.
1. The teeth are dull, caused by cutting
hard material or long use.
2. The saw blade was fitted the wrong way
on the band saw.
1. Replace the saw blade, use a 6 T.P.I.
(Teeth Per Inch) saw blade for wood and
soft material. Use a 14 T.P.I. saw blade
for harder materials. A 14 T.RI. saw blade
always cuts slower due to the finer teeth
and the slower cutting performance.
2. Fit the saw blade correctly.
Sawdust builds up inside the machine.
This is normal
Clean the machine regularly. Open the
doors and remove the sawdust with a
vacuum cleaner.
Sawdust inside the motor housing.
This is normal
Clean the ventilating slots of the motor with
a vacuum cleaner. From time to time re-
move the sawdust to prevent it from being
drawn into the housing.
The machine does not cut at 45 or 90 de-
grees.
1. The table is not at right angles to the
blade.
2. The saw blade is dull or too much pres-
sure was put on the work piece.
1. Adjust the table.
2. Replace the saw blade or put less
pressure on the work piece.
The saw blade can not be properly posi-
tioned on the wheels.
1. The wheels are not in alignment or de-
fective bearing.
2. The blade tracking knob hasn't been
properly adjusted.
3. Inferior saw blade.
1. Replace bearing.
2. Adjust the blade tracking knob (See
ADJUSTMENT
instructions).
3. Replace the saw blade.
_
_rr nzlkzhg izamerf jmmcheee_ Your _
Gmts_u_
° pudu[:L _ [lle_unnd and _
Tnrynam d
_llnemJ_=_
q_mrJ_rt.
I]k.dt likp nil _,
it tony
umquim
u_Mm"
from line kz limp_ Thzzlrswhzm _
=i Flz_r
_
,#gmeme_ ca. _
]mu nmnL_ _1
agil_
_'s
ih,zl
Ilhe llelpair Pmb_dimz _
incllBdes:
Ezped s,_,,ice by our I(].DOD _
mW_ sWe_alis_
!_1 U nFlll_d
_
amd zrm, =1_
rot pml_ im=l Mbmrnn ,,:,q
,==,_mmd mmzim
I_ l_mldrEll_Lam_mmlt upb$1_Dl]ifyuLr_m_l
l_mluEt
€_r_t luefiJ_d
65 iD_.Gount ulf 25n&4[mm m_ulnr puk_ nf _&_
_=1 neJkdml
m Fast henpu_,p_n_ - _ mn _ g_u_ _m=_nn-
_
SUl=tnurl hcnm n _
_.
l"hink _,-,_
=m_a"tnllnng mimers msmunn"
13
Once _uu pmdvme the Repeir Pmkeckzn Agmened.
e
_imple phmle cd is,d IhaL itkd_
rnrymn "In_le
You cat cell a_lime
dey or nigHL,or sdmlule a meek:e
=m:akdm_
online.
]_,=,,==,,=,,a k ,r =.,',j,r,m_undu,ir,a the pm_,,=,,=,d_
p_'iud.
tm rail pmq_e n ful mlhurul. Or. a pmrulm9 udurul mqdim_ uflm-
_
inC_Ia
vzi_, ® _
ihs_,_ IF_ f_l _el_ils
_11 Seam Canada at 1-_1]10-3_1-4_1_.
._n_uS lumtallali_
S mvi_
R_,-_
pu_.lim_
_
af tmme_=_ia'_.
n_nne
du=r upusm_. _ub_r hmmdms, a nd _Jmr maim- hom_ iimms, in _e
U.S.A_ m-Carm_ _dl 14413_-4-IW-140_L__
Publicidad
