English; Important Safety Notices - Duracraft DT-623E Instrucciones De Uso

ENGLISH

IMPORTANT SAFETY NOTICES

Please read all instructions before using the fan. Keep
these operating instructions in a safe place for future
reference.
1. Position the fan where children cannot reach it.
2. Only connect the fan to a single-phase socket with the
voltage specified on the type plate.
3. Always disconnect the plug from the mains when the
fan is not in use, when it is being moved, touched or
cleaned. Do NOT pull on the cable to remove the plug.
4. Completely unwind the cable. A cable which has not
been completely unwound can overheat and cause a fire.
5. Do not use an extension lead or continuous speed
control, since these could overheat, cause a fire or give off
an electric shock.
6. The fan may only be used following the correct assem-
bly of the front grid (1) and the rear grid (6) as described
under "Assembly instructions".
7. The fan must only be used in accordance with the
instructions contained within these operating instructions.
Non-observance of these instructions could result in
injury, cause a fire or give off an electric shock.
8. The fan is for private use in interiors of buildings only. It
is not for commercial use.
9. Do NOT use this fan if it is damaged or could be
damaged, or if it does not work properly. Remove the plug
from the socket.
DESIGN
1. Front grid
2. Plastic nut
3. Blade
4. Protective cover
5. Plastic nut
6. Rear grid
7. Handle
8. Motor shaft
9. Motor
10. Oscillation button
11. Operating switch
12. Fixing knob
13. Fixing knob
14. Base
ASSEMBLY INSTRUCTIONS
1. Pick up the motor (9) and carefully hold it above the
base (14). Firmly press the motor (9) down until it locks
into the base (14). Fix both parts by means of the fixing
knob (13).
2. Loosen the plastic nut (2) in a clockwise direction and
the plastic nut (5) in an anticlockwise direction. Remove
both of them from the motor shaft (8).
3. Place the rear grid (6) onto the motor (9) so that the
handle (7) is pointing upwards and the three guiding slots
are positioned to the left, right and underneath of the
motor shaft (8).
4. Fix the rear grid (6) by turning the plastic nut (5) firmly
in a clockwise direction.
5. Remove the protective cover (4) from the motor shaft (8).
6. Place the blade (3) onto the motor shaft (8) so that both
guiding slots rest on the rear of the blade (3) on the
mounting pin.
7. Turn the blade (3) with the plastic nut (2) in an
anticlockwise direction, holding the blade (3) whilst doing
so.
8. Loosen the fixing screw from the rear grid (6) and open
the side clips. Put the front grid (1) into the mount on the
underside of the rear grid (6) and align the screw holes
on the upper side so that they are positioned above each
other. Now secure the two grids with the two side clips
and then tighten the fixing screw and nut with a
screwdriver.
OPERATING INSTRUCTIONS
1. Place the fan on a flat, dry surface.
2. Check that the operating switch (11) is on position OFF
(0). Put the plug into the socket.
3. Turn the operating switch (11) to the desired position:
0 OFF
1 Low speed
2 Medium speed
(High speed only with the DT-623E)
3 High speed
4. Loosen the fixing knob (12) on the side of the motor
and tilt the fan to the desired position. Then retighten the
fixing knob (12).
5. Press the oscillation button (10) in order to activate
oscillation of the fan from left to right. Pull the oscillation
button (10) out in order to deactivate oscillation.
6. Please use the handle (7) on the rear grid
(6) for carrying the fan.
7. Turn the operating switch (11) to the OFF position (0)
and remove the plug from the socket when not in use.
4