Publicidad
Idiomas disponibles
Idiomas disponibles
CqE>
(1-2) ASSEMBLEY
Royal 46
Set the rear wheels of the mower to
maximum cutting height.
Attach the lower section of the
handlebar as illustrated.
Insert the bolts from the inside, and
tighten the nuts from the outside. Note:
Don't forget washers.
(3)
Assemble the upper handlebar so
that the switch box is facing upwards.
Insert the bolts from inside as shown.
N.B.! Don't forget the washer between
the wing nut and the handlebar.
(4) Fasten the cables to the handlebar
with the clips.
(5) ASSEMBLEY
Royal 47
Unfoid the handle with care. Avoid
damaging the cables. Tighten the wing
nuts.
GRASS COLLECTOR
Royal 46
(6) Assembly
Insert steel frame Into grass collector
bag.
Fasten plastic rails to the steel frame.
(7) Fit the right and left hand pegs of the
grass collector frame Into their
respective ears on the front section of
the collector. Secure both pegs with "R"
clips.
(8) Raise the safety flap. Place the grass
collector over the ejection chute. Lower
the grass collector until it is supported by
the lower handle sections and place the
safety flap over the front section of the
collector.
(9) Emptying
The grass collector can be emptied
without removing it from the mower, by
pivoting the rear section upwards. It can
also be emptied by removing it from the
mower and opening in the manner
shown in the illustration 9.
GRASS COLLECTOR
Royal 47
(10) Assembly
Raise the safety flap. Place the grass
collector over the ejection chute. Lower
the grass collector until it is supported by
the lower handle sections and place the
safety flap over the front section of the
collector.
(11) Emptying
Swing open collector top and remove
grass. See illustration 11.
(12) 3 CUTTING HEIGHTS
Switch off the power at the power switch
(setting 0) and remove the key to
prevent unintentional starting. The
mower can be adjusted to 3 different
cutting heights. Move the axles between
the notches to achieve the desired
cutting height.
(13) 7 CUTTING HEIGHTS
Adjust to the desired cutting height by
means of the lever on the right side of
the mower.
(14-15) BATTERY CHARGING
Charge the battery before using for the
first time. Thereafter the battery should
always be charged after use.
•
Turn the power switch to setting 0 .
• Connect the chargercable to the
socket.
•
Connect the chargercable to the
mains supply.
•
Time to recharge approx. 12 hours
(when battery is fully charged, one
green light is flashing).
•
Approx. 4 hours to 80% charging.
•
When charging is complete, remove
the chargercable.
(16) What the display shows
3 green lights
= Battery 100%
2 green lights
= Battery 50%
1 green light
= Battery 25%
1 green light flashing= Battery 5%
1 red light flashing
= Too heavy load
1 red light
= Stopped, overload
When charging the green lights will light
up in reverse order.
At maintenance charging
one
green light
is flashing slowly.
START AND STOP
(17-18) Starting the mower.
Always start the mower in short grass or
on a flat surface. Check that the power
cable is not trapped or damaged. Turn
the power switch to setting 1. Hold down
the safety loop and turn the starter key.
The key will spring back automatically.
Start to mow when the motor runs at
normal speed.
(19) Stopping the mower
Release the safety loop. Always switch
off the power at the power switch
(setting 0) and remove the key to
prevent unintentional starting when you
leave the machine.
Always charge the
battery after use!
(20)
USE
Mowing on slopes can be dangerouse.
Do not mow on very steep slopes.
Always cut along the slope. Overloading
the mower can be avoided by making
sure the motor speed does not drop
unduly. In long grass a first cut with the
blade Sjet higher will reduce the load.
(21) Before mowing, objects such as
twigs, toys and stones should be
removed from the lawn.
Avoid
running the blade over foreign
objects such as stones, roots, etc., as it
may cause engine damage.
(22) Mow the lawn twice weekly during
the most active periods of growth. Never
cut more than 1/3 of the length of the
grass, especially during dry periods.
Mow with a high cutting height setting
the first time. Examine the result and
lower the mower to the desired setting.
Mow slowly or mow the grass twice if it
is very long.
(23) If the ejection chute gets glogged,
do the following: Switch off the power at
the power switch (setting 0) and remove
the key to prevent unintentional starting.
Remove the grass collector and clean
the ejection chute.
(24) MAINTENANCE
WARNING! Always switch off the power
switch (setting 0) before cleaning,
servicing or repairing the mower. Also
remove the key to prevent unintentional
starting.
(25) After use
Brush off all grass, leaves, etc. (Do not
use a high pressure washer). The
batteries are entirely sealed so the
mower can be tilted freely without
battery acid running out.
(26) Annnualiy (after end of season)
Check the condition of the blade.
Service or replace the blade If
necessary. Grinding and balancing the
blade: Switch off the power at the power
switch (setting 0) and remove the key to
prevent unintentional starting. Unbolt the
blade and leave it with a service station
for grinding and balancing. Tighten the
blade bolts correctly. Tightening torque:
35 - 40 Nm.
(27) Changing the battery
Do not remove the batteries unless you
are replacing them. Take special care
when changing the batteries (removing,
connecting) and when handling them.
Make sure you do not short circuit them.
A short circuit can damage the machine
and cause the batteries to explode. Do
not change the batteries yourself unless
you are absolutely sure how they should
be connected. Always change both
batteries at the same time.
The batteries are sealed lead batteries
that contain corrosive acid. If the acid
should come into contact with the eyes,
rinse thoroughly with plenty of water and
seek medical attention. If the acid comes
into contact with the skin, rinse
thoroughly with plenty of water and
protect the eyes from possible
splashing.
(28)
Take care of used batteries and
take them to a battery collection station.
(29)
Rear discharge deflector is optional.
GENERAL INFORMATION
(30) Transport
Switch off the power at the power switch
(setting 0) and remove the key to
prevent unintentional starting. Carefully
folding the handle. Avoid damaging the
cable and the display.
Winter storage
Always charge the battery before storing
for the winter.
To maintain the battery in its best
condition it is a good ruie to charge the
battery once during the winter period.
Service
When ordering spare parts, aiways
quote the mower's product no.
22
Publicidad
