Safety Guidelines - Definitions - BLACK&DECKER CE750 Manual De Instrucciones

often you do this type of work.
To reduce your exposure to these chemicals:
► work in a well ventilated area, and work with
approved safety equipment, such as those dust
masks that are specially designed to filter out
microscopic particles.
► Avoid prolonged contact with dust frompower
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing
and wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmful chemicals.
Warning! Use of this tool can generate and/or disperse
dust, which may cause serious and permanent respiratory
or other injury. Always use NOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles
away from face and body.
Warning! Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19) during use.
Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
SAFETy GUIDELINES/DEFINITIONS
It is important for you to read and understand this manual.
The information it contains relates to protecting yOUR
SAFETy and PREVENTING PROBLEMS. The symbols
below are used to help you recognize this information.
Danger! Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
Warning! Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
Warning! Indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate injury.
Warning! Used without the safety alert symbol indicates
a potentially hazardous situation which, if not avoided, may
result in property damage.
► When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The table shows the
correct size to use depending on cord length and
nameplate ampere rating. If in doubt, use the next heavier
gage. The smaller the gage number, the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50
(0-7,6m) (7,6-15,2m)
240 V 0-50 51-100
(0-15,2m) (15,2-30,4m)
Ampere Rating
More Not more American wire gage
than than
0 - 6 18
6 - 10 18
10 - 12 16
12 - 16 14
FEATURES (Fig. A)
1. Trigger switch
2. Lock-on button
3. Depth adjustment knob/front handle
4. Switch handle
5. Shoe
6. Chip discharge chute
7. Chip deflector lever
8. Vac adaptor
9. Wrench
10. Blades
11. Blade guard (not shown)
OPERATION
Switch (Fig. B)
Caution! Check that the tool is not locked ON before
connecting it to a power supply. If the trigger switch is locked
ON when the tool is connected to the power supply, it will start
immediately. Damage to your tool or personal injury may result.
Caution! Allow the tool to reach full speed before touching
tool to the work surface. Lift the tool from the work surface
before turning the tool off.
To start the planer, depress the trigger switch (1) in Fig. B.
To turn the planer off, release the trigger switch.
Lock-On Button (Fig. B)
The tool can be locked on for continuous use. To lock the tool
ON depress the trigger switch (1) and push in the lock-on
button (2). Hold the lock-on button in as you gently release
the trigger switch. The tool will continue to run.
To turn the tool OFF from a locked-on position, squeeze and
release the trigger once.
Adjusting Planing Depth (Fig. C)
Warning! Turn off and unplug the tool before making any
adjustments or removing or installing accessories.
Planing depth is infinitely variable from 0 to .5/64ths in.
(2.0 mm). To adjust the cutting depth, rotate the depth
adjustment knob/front handle (3) clockwise from the "P"
position. The cutting depth will increase from 0 to as
much as .079 in. (2.0 mm).
ENGLISH • 19
51-100 101-150
(15,2-30,4m) (30,4-45,7m)
101-200 201-300
(30,4-60,9m) (60,9-91,4m)
16 16 14
16 14 12
16 14 12
12 Not recommended