HIKOKI RP18DA Instrucciones De Manejo página 11

How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its
life will become shorter.
(2) Avoid recharging at high temperatures. A rechargeable
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery
life will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Remaining battery indicator
Selecting accessories
PRIOR TO OPERATION
WARNING
Be sure to turn off the switch and disconnect the
battery.
1 Attaching the accessory storage (Fig. 4)
The bracket and two Philip's head screws are in the
tank.
Attach the bracket to the vacuum housing using the
screws.
2 Use a dust bag (Fig. 5)
(1) Switch off the device and open the clamps.
Remove the upper part of the device from the tank.
(2) Insert a dust bag in the tank.
Put the upper part back on and close the clamps.
Remove the dust bag for wet vacuuming.
3 Shoulder strap (Fig. 6)
If required, hook the shoulder strap into both eyelets
left and right of the device. Set the shoulder strap to the
desired length.
Carrying:
WARNING
The device must be carried only with the supplied
shoulder strap provided.
The device must NOT be carried with the shoulder
strap around your neck.
THE DEVICE
1 Switching on/off (Fig. 7)
Use the switch to turn the device On/Off .
Level II: High suction power
-
Level I: Medium suction power
-
Level 0: Off
2 PressClean (Fig. 8)
To clean the fi lter using a strong air fl ow:
Put the switch in position II, cover the nozzle or suction
opening with the hand and press the button several times
(at least 3 times).
USE
Figure Page
1 This device is suitable for dry and wet applications
2 2
The device must not be switched on without fi lter in place.
3 2
Wet vacuuming
○ Remove the dust bag for wet vacuuming.
10 4
○ The device switches off automatically once the
― 217
maximum water level has been reached.
WARNING
The device is not switched off when the tank is full
for non-conductive liquids (such as emulsion drilling
fl uids, oils and greases).
The fi ll level must be monitored continuously and the
tank must be emptied promptly.
NOTE
○ If water is suctioned quickly, then you will not be able to
suction as much as if water is suctioned slowly.
○ The fi lter will get wet when suctioning water.
Ensure that it has suffi cient time to dry and that all
components are completely dry before using the
device for dry vacuuming.
○ If the water switch-off does not work and fl uid is
suctioned into the motor so that water comes out of
the device, stop the device. Allow the device to dry
suffi ciently.
After wet vacuuming: clean the fi lter after drying it
completely with the fi lter cleaning element.
Clean the electrodes of stainless steel with steel brush if
any contaminations on them. Clean the tank with a moist
cloth and dry it off .
Dry Vacuuming
Vacuum only with dry fi lter, device and accessories. If the
cartridge is damp, dust may stick and form a crust.
For dry vacuuming dust bags are recommended to use.
Using as a blower
Use with the fl exible hose inserted into the blow port.
2 Transport
Store the fl exible hose on the housing.
The upper part must be securely sealed to the tank - check
that the clamps are closed.
Set the switch to position "0". (Fig. 7)
3 Using accessories
When using the wide nozzles and/or tube, we recommend
mounting the nozzle between the hose and the wide
nozzles/extension wands in use.
11
recommended for profi led surface such as carpets.
recommended for smooth surfaces.
English