Publicidad
Idiomas disponibles
Idiomas disponibles
POLESAW
INFORMATION
POLESAW ASSEMBLY
_1_ WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
I.
2.
Remove battery from chain saw.
Separate main handle from chain saw
power head by pressing both release
buttons
on main handle
and pulling
apart (see Figure 21).
Press
Release
Release
Button
Buttons
Figure 21 - Separate
Main Handle from
Powerhead.
3.
Align rib on chain saw power head with
groove in power head adapter on pole
(see Figure 22).
Groove
Power
Head
"
,,
Polesaw
Power Head
Adapter
Figure 22 =Align Power Head with Power
Head Adapter
4.
Slide power
head into power
head
adapter until units "snap" together (see
Figure 23). IMPORTANT" Both release
buttons on power head adapter must be
fully engaged.
Figure 23 - Assembled Power Head and
Power Head Adapter
5.
Align rib on handle adapter
on pole
with groove in main handle (see Figure
24).
Groove
/
/
/
Rib/_
\\\\\
Polesaw
\,
Handle"-\
Adapter
Main Hdhdle
Figure 24 =Align Main Handle with Ham
die Adapter
6.
Slide main handle into handle adapter
until units "snap" together (see Figure
25). IMPORTANT: Both release
but-
tons on main handle
must be fully
engaged.
Figure 25 - Assembled Main Handle and
Handle Adapter
7.
Slide battery onto main handle until
release
buttons
"snap"
together
(see
Figure 26).
Note: Fully charge battery beti)re using
tk)r first time. See Charging
Battery,
page 10
Figure 26 - Assembled
Battery
onto Main
Handle
ADJUSTING
POLE LENGTH
The Remington
brand polesaw has a tele-
scoping pole assembly that will extend from
47 inches (fully retracted) to 83 inches (fully
extended).
A cam levered collet is used to
hold the pole in position at any extended
length.
1.
To extend the pole, loosen the clamping
lever (see Figure 27). Pole will slide
freely.
2.
Pull inner pole section out to desired
length of extension. Note: Only extend
pole to minimum
length required
to
reach limb that is being cut.
3.
To lock pole in position, tighten clamping
lever (see Figure 27).
UNLOCK
LOCK
Figure 27 - Extending Telescopic Pole
CUTTING WITH THE POLESAW
I.
Attach battery to saw.
2.
Use both hands to grip polesaw. Use
only designated grip areas when oper-
ating polesaw (see Figure 28). Use firm
grip. Thumbs and fingers must wrap
around polesaw handle and pole.
3.
Make sure your ti_ofing is firm. Keep
feet apart. Divide your weight evenly
on both feet.
f
Figure 28= Designated
Grip Areas
4.
When ready to make a cut, press in
trigger lockout and squeeze trigger (see
Figure 29). This will turn polesaw on.
Releasing trigger will turn polesaw off.
Make sure saw is running beti_re starting
a cut.
5.
When starting
a cut, place moving
chain
against
wood. Hold polesaw
firmly in place to avoid possible bounc-
ing or skating (sideways movement)
of
saw.
6.
Guide polesaw using light pressure. Do
not ti_rce saw. The motor will overload
and can burn out. It will do the job bet-
ter and safer at the rate for which it was
intended.
7.
Remove
polesaw from a cut with saw
running, at full speed.
Stop polesaw by
releasing trigger. Make sure chain has
stopped before setting polesaw down.
Trigger
Trigger Lockout
Figure 29- Polesaw Handle with Trigger
Lockout
15
Publicidad
