Behringer HELLBABE HB01 Manual De Instrucciones página 2

2
HELLBABE HB01
1. Controls
This is the PEDAL of the HB01. The unit will be activated as soon
(1)
as you put your foot on and move it. By taking your foot from
the pedal the effect will be deactivated. Depending on the timer
adjustment (see (10)) the HB01 remains active for a few seconds
after that.
The RANGE control lets you extend the heel-down frequency
(2)
to match the frequency range of bass guitars for example
(440 Hz to 250 Hz).
The BOOST switch activates the boost function. The output level
(3)
is then increased - but only if the Wah effect is switched on.
The BOOST control adjusts the level of output boost
(4)
(max. +15 dB). This control is only active if the BOOST switch
is set to ON (and if the Wah is switched on).
The Q control allows to change the shape of the filter peak.
(5)
High Q settings (turned to right position) produce a large,
selective filter peak with a high output level. Low Q settings
(turned to left position) provide a lower output level
with a subtle, broad filter peak producing less vocal effect.
Turning the FINE control allows to extend the toe-down
(6)
frequency of the sweep range up to 2.2 kHz.
Use this 1/4" TS IN connector to plug in the instrument cable.
(7)
The 1/4" TS OUT connector sends the effected signal to your amp.
(8)
The 1/4" TS OUT/BYPASS connector can be used as second output or
(9)
as bypass, hard wired to the input, to play out the uneffected signal.
The TIMER ADJ control (accessable through a hole in the housing)
(10)
is needed to adjust the time the effect remains active
after taking your foot from the pedal.
Use the 9 V connection to plug in a 9 V power supply (not included).
(11)
The STATUS-LED illuminates when the effect is activated.
(12)
The BOOST-LED illuminates when the boost function is activated.
(13)
The ROCKER SCREW allows to adjust the resistance
(14)
of the rocker mechanism.).
The BATTERY COMPARTMENT is located on the bottom.
Open the lid to install or replace the 9 V battery.
◊ ◊
The HB01 has no on/off switch. As soon as you insert the jack
into the IN connector, the HB01 begins running. When not
using the HB01, remove the jack from the IN connector.
This extends the life of the battery.
The SERIAL NUMBER is located at the bottom of the unit.
2. Safety Instructions
Do not use near water, or install near heat sources. Use only authorized
attachments/accessories. Do not service product yourself. Contact our
qualified servicing personnel for servicing or repairs, especially when
power supply cord or plug is damaged.
3. Limited Warranty
For the applicable warranty terms and conditions and additional
information regarding Music Tribe's Limited Warranty, please see
complete details online at community.musictribe.com/pages/
support#warranty.
4. Specifications
Input
Connector 1/4" TS
Impedance 1 MΩ
Output
Connector 1/4" TS
Impedance 1 kΩ
Output/Bypass
Connector 1/4" TS
Impedance 1 kΩ
Power Supply
PSU-SB-CN Behringer
PSU-SB-EU Behringer
PSU-SB-JP Behringer
PSU-SB-SAA Behringer
PSU-SB-UK Behringer
PSU-SB-UL Behringer
Power connector
Battery
Power consumption
Physical/Weight
Dimensions
(H x W x D)
Weight
Behringer is constantly striving to maintain the highest professional standards. As a result
of these efforts, modifications may be made from time to time to existing products without
prior notice. Specifications and appearance may therefore differ from those listed or shown.
3 3
User Manual
9 V , 100 mA DC, regulated
220 VAC adaptor China
230 VAC adaptor Europe
100 VAC adaptor Japan
240 VAC adaptor Australia
240 VAC adaptor UK
120 VAC adaptor USA
2 mm DC jack, negative center
9 V type 6LR61
30 mA
3.8 x 4.7 x 10"
99 x 120 x 254 mm
2.6 lbs / 1.2 kg