cecotec READYWARM 2050 MAX CERAMIC ROTATE SMART Manual De Instrucciones página 17

ENGLISH
Box content
- Heater
- Remote control
- Instruction manual
3. OPERATION
Assembly
- Fit the two supplied parts of the bracket together and slide the upper part to the left, as
shown in figure 4.
- Place the main frame of the apparatus on a stable table. The bottom of the main frame
should protrude slightly over the edge of the table. Place the bracket on the bottom of the
structure. The four holes in the bottom of the frame must fit exactly into the four holes
in the bracket as shown in figure 5. Screw the bracket on by hand using the four screws
provided. Do not overtighten the screws.
- Ensure that the bracket is straight and firmly attached to the underside of the structure.
- Place the device in the bracket.
Operation
1. Plug in the appliance.
2. Press the on/off switch on the back of the appliance. The heater will switch on in Standby
mode, beep and the display will show the room temperature.
3. Press the on/off touch icon on the control panel or the power selector button on the
remote control to select between the different modes:
A. Medium power: press once. The indicator light will turn blue indicating that the medium
power mode is active.
B. High power: press once. The indicator light will turn red indicating that the high power
mode is active.
C. Standby: press a third time. The indicator light will turn off (except the display). The heater
will expel the remaining hot air for 15 seconds, showing the countdown on the display and
flashing 3 times when it reaches "00". It will then return to displaying the room temperature.
4. Press the oscillation touch icon to activate or deactivate the oscillation function.
5. Press the timer touch icon to activate the timer, you can set the timer between 1-24h.
6. Press the temperature touch icon to adjust the temperature between 15-40°C. During
operation, press the touch icon to cancel the temperature presetting.
The heater will switch off automatically if the ambient temperature exceeds 50°C.
Please note the following aspects of the heater's operation:
- After the heater is turned on, if the set temperature is 4˚C higher than the room temperature,
the heater will continue to heat in high power mode until it reaches the set temperature.
32
READYWARM 2050 MAX CERAMIC ROTATE SMART
- After switching on the heater, if the set temperature is 2-3°C higher than the room
temperature, the heater will continue heating in medium power mode until it reaches the
set temperature.
- Once the room temperature is 2°C higher than the set temperature, the heater will stop its
operation.
- Press and hold the temperature touch icon and the timer touch icon for 3 seconds or press
the lock button to unlock the lock function.
- By pressing and holding the oscillation button on the fan heater, you can put the display
to sleep and turn off the light. To reactivate the display, simply press any key on the fan
heater.
Remote control
- Power button: press this button to turn the device on or off.
- Oscillation button: press this button to activate/deactivate the oscillation of the appliance.
- Timer button: press this button to activate the timer, you can set the timer between 1-24h.
- Power selector button: press this button to select the power you want. You can choose
between medium power (blue indicator), high power (red indicator) or standby (off
indicator).
- Temperature button: press this button to adjust the temperature between 15-40°C.
- Lock button: press this button to lock/unlock the device.
4. CLEANING AND MAINTENANCE
- Before cleaning and maintenance, make sure that it is disconnected from the mains.
Cleaning and maintenance may only be carried out when the heater is completely cool.
- Clean the heater with a soft cloth with neutral detergent and dry it. Do not use other
solvents.
- The heater only needs to be cleaned externally.
- After cleaning and maintenance, make sure it is completely dry before use or storage.
- Clean it if it is not going to be used for a long period of time. Store it in a dry place.
5. TECHNICAL SPECIFICATIONS
Product reference: 08279
Product: ReadyWarm 2050 Max Ceramic Rotate Smart
Power: 2000 W
Voltage: 220 - 240 V
Frequency: 50 - 60 Hz
ENGLISH
READYWARM 2050 MAX CERAMIC ROTATE SMART
33