Publicidad
Idiomas disponibles
Idiomas disponibles
Washer leaks
•
Check the following:
Are the fill hoses tight? Are the fill hose washers properly
seated? Is the drain hose clamp properly installed? (See
"Installation
Instructions.")
Residue or lint on load
•
Did you add detergent to the dispenser?
For best results, use the dispenser to dissolve the detergent.
•
Is the sink or drain clogged?
Sink, floor drain and standpipe must be able to handle 17 gal.
•
(64 L) of water per minute.
•
Is water bouncing off the tub ring or the load?
The wash load should be balanced and not overloaded.
If
not, the fill or spray rinses can bounce off the load.
The washer must be level. The front and rear feet should be
properly installed and the nuts tightened.
Reset the self-
adjusting rear feet if needed. (See "Installation
Instructions.")
•
Did you pull the drain hose from the washer cabinet and
install it in a standpipe or laundry tub?
See "installation
Instructions."
•
Was a cycle interrupted and then the CATALYST ®
Cleaning Action selected?
The CATALYST®Cleaning Action should be started on a dry
load only.
The CATALYST®Cleaning Action should not be selected after
the tub has started filling with water.
•
Check household plumbing for leaks.
Washer basket is crooked
•
Is the load balanced and the washer level?
The wash load should be balanced.
Did you sort properly?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
Did you overload the washer?
The wash load must be balanced. See "Starting Your
Washer" for maximum load size. Lint can be trapped in the
load if overloaded. Wash smaller loads.
Was paper or tissue left in pockets?
Did you use enough detergent?
Follow manufacturer's
directions.
Use enough detergent to
hold the lint in the water.
Is your water colder than 65°F (18°0)?
Wash water colder than 65°F (18°C) may not completely
dissolve the detergent.
Are you using a gentle wash cycle?
Consider using liquid detergent for slow speed settings such
as Handwash, Casual or Delicate.
Stains on load
•
Did you add detergent to the dispenser?
For best results, use the dispenser to dissolve the detergent.
•
Did you use enough detergent?.
Use enough detergent to remove soil and hold it in suspension.
Add the manufacturer's
recommended
amounts.
The washer must be level. The front feet should be properly
•
installed and the nuts tightened. Reset the rear leveling legs,
if needed. (See "installation
Instructions.")
Dispensers
clogged or leaking
•
Are the laundry products in the correct dispenser?
Add the correct amounts of detergent (powder or liquid),
•
liquid chlorine bleach, or fabric softener to the correct
dispenser. You can add powder or liquid color safe bleach to
the detergent dispenser. Be sure to match powdered color-
•
safe bleach with powdered detergent or match liquid color-
safe bleach with liquid detergent. Use only liquid chlorine
bleach in the bleach dispenser.
Load too wet
•
Did you use the right cycle for the load being washed?
Select a Speed control setting with a higher spin speed.
•
Did you use a cold rinse?
Cold rinses leave loads wetter than warm rinses. This is normal.
Did you add fabric
softener directly to the load?
Use your fabric softener dispenser. Do not drip fabric softener
on clothes.
Is there above average
iron (rust) in water?.
You may need to install an iron filter.
Did you properly sort the load?
Sort dark clothes from whites and lights.
Did you unload the washer promptly?
To avoid dye transfer, unload the washer as soon as it stops.
Did you use a fabric
softener dispensing ball?
Use the fabric softener dispenser provided with the washer.
Dispensing balls will not operate correctly with this washer.
Did you use powder detergent
in a low speed cycle?
Consider using liquid detergent.
Did you add detergent,
chlorine bleach or fabric softener
too late in the cycle?
Detergent, chlorine bleach, and fabric softener should be
added to the dispensers before starting the washer.
17
Publicidad
