Publicidad
English
Battery precautions
1. Do not use rechargeable batteries.
2. Use only alkaline AA batteries of the same or equivalent type.
3. Insert batteries with the correct polarity
4. Keep batteries away from children.
5. Dispose of exhausted batteries according to local legal
requirements. Do not dispose of them by throwing away with
normal household rubbish.
6. Avoid short circuiting the contacts in the battery compartment
and battery terminals.
7. Remove batteries from the unit if it will not be used for a long
period of time.
8. Exhausted batteries should be removed from the battery
compartment to prevent over-discharging, which can cause
leakage and may cause damage to the clock.
Battery installation
1. Insert 1xAA (1.5V) battery observing the correct polarity, as
shown on the diagram.
2. Replace battery cover.
Radio controlled operation DCF version
(Germany & European countries)
This Braun alarm clock is set and controlled automatically by DCF
radio signal. The DCF radio time code signal is broadcast from
Frankfurt, Germany. The coverage of the DCF signal is the whole
of Germany. The time code signal can be received up to 1500km
from Frankfurt. This covers most of Central and Western Europe.
Radio controlled clock operation
1. We strongly recommend you start your clock at night. Once
the battery is installed properly, the clock automatically sets
itself to 12 o'clock and then begins receiving the signal. Once it
has received the DCF signal and processed it accordingly (which
takes 3 to maximum 12 minutes), the clock will automatically
display the correct time.
2. If the clock still has not set itself after 12 minutes, reception is
faulty or not possible at the chosen location. Repeat setting at a
different location by pressing the RESET button.
A time check is carried out during every odd hour and the time is
compared with the radio signal and will be corrected if necessary.
Each time it will take 3 -12 minutes to receive the radio signal.
Important
For best reception performance, please read the following in-
structions.
1. Place the unit away from interfering sources such as TV set,
computers, microwaves, etc.
2. Avoid placing the unit on or next to metal surfaces.
3. Avoid closed areas such as airports, basements, cement office
buildings or factories.
Note: Exposure to an electrostatic environment may cause the
clock to reset. In this event please follow the instructions as
described in this manual to set the clock again.
Manual time setting
1. Press and hold the TIME SET button for 3 - 4 seconds to enter
the time setting.
2. Press the TIME SET button for 1 second to advance 1 minute, or
3. Press and hold the TIME SET button for more than 2 seconds to
speed up the time setting to the desired time.
4. If the TIME SET button is not pressed for 8 seconds, the clock is
set.
Important: Once the desired time is set manually, the clock will
correct itself to a Radio Controlled time once a valid signal is
received.
Alarm setting
To set the alarm follow below procedures:
1. Press the ALARM SET knob located at the back of the clock, the
rotating switch will pull outwards.
2. Turn the knob in the direction of the arrow until desired alarm
time is shown, only turn in the direction of the arrow to avoid
damaging the movement.
3. Press the ALARM TAB located on the top to activate the alarm,
green bar will be shown at the front.
4. Press back the ALARM SET knob located at the back of the
clock.
Alarm / snooze function
When the alarm time is reached, the alarm will sound for a
maximum of 2 minutes if the ALARM is ON and the SNOOZE /
LIGHT button is not pressed. It is reactivated 12 hours later at
the same time. Press the alarm tab on the top to stop the alarm.
The SNOOZE / LIGHT button is located at the bottom of the clock
housing and can be activated when pressing on the clock body
downwards. To activate the snooze function again press the clock
body downwards and the alarm will stop with light turns on for 5
seconds and resumes after approximate 5 minutes interval. The
snooze function can be repeated 3 – 7 times.
Illumination
1. To be able to read the face of your alarm clock when it is
dark, briefly press on the top of the alarm clock to activate the
SNOOZE/LIGHT button at the bottom.
2. The illumination function is activated for 5 seconds.
Reset function
The clock has a hands setting help function. By pressing the reset
button at any time, the hands will automatically move to the 12
o'clock position and then receive signal.
Note: Pressing the SNOOZE/LIGHT button while the clock is being
reset to 12 o'clock or while the clock is receiving Radio Control
Signal can cause interference with Radio Control reception.
Guarantee
2 year guarantee against material and workmanship defects
(except battery). The guarantee is valid in those countries where
the alarm clock is officially being sold.
Broken or cracked lens screens are not covered under the
Guarantee.
Braun helpline
Should you have a problem with your product, please check your
local service centre at:
www.braun-clocks.com
www.braun-watches.com
or contact +44 808 175 3235 (calls free within the UK) or +44 208
208 1833.
WARNING! This product is covered by the Waste Electrical
and Electronic Equipment (WEEE) directive. It should not be
discarded with normal household waste but taken to your local
collection centre for recycling.
EU Declaration of Conformity
We ZEON LIMITED UK, manufacturer of Braun Watches & Clocks
under licence from the Procter & Gamble Company hereby
declare that model BC07-DCF conforms to Directive 2014/53/
EU. The full text of the EU Declaration of Conformity can be
viewed on our website at www.braun-clocks.com
Frequency band : 77.5KHz
Transmit power : 0 dBm
Certain trademarks used under license from The Procter &
Gamble Company or its affiliates.
Publicidad
