Craftsman professional 351.228051 Manual Del Operador página 10

• Plug must be plugged into matching outlet that is properly
installed and grounded in accordance with all local codes and
ordinances. Do not modify plug provided. If it will not fit in
outlet, have proper outlet installed by a qualified electrician.
• Inspect tool cords periodically and if damaged, have them
repaired by an authorized service facility.
• Green (or green and yellow) conductor in cord is the
grounding wire. If repair or replacement of the electric cord
or plug is necessary, do not connect the green (or green
and yellow) wire to a live terminal.
• Many cover plate screws, water pipes and outlet boxes are
not properly grounded. To ensure proper ground, grounding
means must be tested by a qualified electrician.
EXTENSION CORDS
The use of any extension cord will cause some drop in
voltage and loss of power.
Wires of the extension cord must be of sufficient size to
carry the current and maintain adequate voltage.
Use the table to determine the minimum wire size (A.W.G.)
extension cord.
Use only 3-wire extension cords having 3-prong grounding
type plugs and 3-pole receptacles which accept the tool plug.
If the extension cord is worn, cut, or damaged in any way,
replace it immediately.
Extension Cord Length (230V Operation)
Wire Size A.W.G.
Up to 50 ft....................................... 14
50 to 100 ft ....................................... 12
NOTE: Using extension cords over 100 ft. long is not
recommended.
Refer to Figures 7-12, pages 17-27.
DESCRIPTION
The Craftsman 10" Model Number 228051 and 12" Model
Number 228031 tilting arbor saws, offer precise cutting perfor-
mance for all woods up to 3" thick (10" saw) and 4" thick (12"
Saw). The saws are designed for the professional user and
are ruggedly constructed for continuous service. The saws are
designed to be permanently located in a shop or plant. The
10" Saw is recommended for use with a 10" blade and the
12"Saw is recommended for use with a 10" or 12" blade.
The saws feature an extra large solid cast-iron table. A unique
system of T-slots incorporates the cast iron miter gauge as
well as two rip fence alignment T-blocks. Saws are equipped
with a clear acrylic blade guard and antikickback feature.
Cabinet is constructed of heaw gauge welded steel, totally
enclosed and is ported for a 4" vacuum hose.
Saws include: 5/8"dia. arbor, %" dia. dado arbor, 1" dia. arbor
(12" saw only), dado table insert, and a three V-belt drive sys-
tem.
Rip Fence Assemblies, feature heavy-duty precision rip
fences that are designed for simple and one-hand maneuver-
ability. They include a front rail calibrated in inches and mil-
limeters with a magnified window for close tolerances.
SPECIFICATIONS
MODEL 228051
10" TILTING ARBOR TABLE SAW
Capacity with 10" Blade:
Depth of cut at 90 ° . ............................... 3"
Maximum tilt angle of arbor ........................ 45 °
Depth of cut at 45 ° . ............................. 21/8 ''
Max. cut right of blade with rip fence ................. 50"
Max. cut left of blade with rip fence .................. 10"
Saw Dimensions:
Table height .................................... 34"
Cabinet depth ................................. 191/2' '
Cabinet width .................................. 211/2"
Table area ................................. 37" x 27"
Front of table to blade ............................ 12"
Rip Fence Dimensions:
Rip fence ..................................... 36%"
Rip fence rails (front and rear) ................... 77, 73"
Blade capacity maximum .......................... 10"
Blade arbor extension ............................. 8/8"
Dado blade capacity maximum ..................... 13/18"
Dado blade arbor extension ........................ 8/8"
Saw Constructions:
Cabinet ................... Totally enclosed welded steel
Table ................................. Solid cast iron
Rip fence ..................... Aluminum and steel tube
Drive system ............................ Three V-belts
Exhaust port ................................ 4" Male
Miter gauge .............. Cast iron with T-slot roller guide
Blade guard .............. Acrylic with antikickback pawls
Switch ............. Locking magnetic starter with overload
Arbor R.P.M........................ 4,000 RPM approx.
Motor: .................. 3HP, 3450 RPM, capacitor start,
capacitor run, 230V, 16A, single-phase, ball bearing,
Sears Part No. 23058.00
Gross weight with motor ....................... 490 Ibs
MODEL 228031
12" TILTING ARBOR TABLE SAW
Capacity with 12" Blade:
Depth of cut at 90 ° . ............................... 4"
Maximum tilt angle of arbor ........................ 45 °
Depth of cut at 45 ° . ............................. 23/4"
Max. cut right of blade with rip fence ................. 50"
Max. cut left of blade with rip fence .................. 91/8 ',
Saw Dimensions:
Table height .................................... 34"
Cabinet depth ................................... 23"
Cabinet width ................................... 26"
Table area ................................. 48" x 30"
Front of table to blade ........................... 123/4 ''
10