Redmond RMG-1212-7-E Manual Del Usuario página 10

Manufacturer reserves the right to make any modifications to design, packaging, or technical specifications of the product
without prior notice.
Meat grinder parts A1
1. Motor unit
2. ON/OFF button
3. Reverse mode button REV
4. Drive shaft clutch
5. Grinder unit release button
6. Loading tray
7. Dismountable pusher with attachment storage capacity
8. Meat grinder unit
9. Screw
10. Blade
11. Perforated disks with holes of different diameter
12. Locking knob
13. Kebbe attachment base
I. BEFORE THE FIRST USE
Carefully remove the unit and its accessories from the packaging. Dispose all packaging materials and promotional stickers.
Keep all warning labels, warning stickers (if any), and the serial number identification label located on the housing. The absence
of the serial number will deprive you of your warranty benefits!
After transportation or storage at low temperatures allow the appliance to stay at room temperature for at least 2 hours before using.
Wipe the motor unit with a moist cloth. Wash all removable parts, strictly following the instructions in "Cleaning and main-
tenance". All the removable parts should completely dry at room temperature before the assemblage. Ensure that outer and
inner visible parts of the grinder do not have faults, splits and other defects.
II. OPERATION
The meat grinder REDMOND RMG-1211-7-E is a multifunctional appliance for food processing.
See the appliance usage procedure on the corresponding schemes: making mince — A2, making sausages — A3, making
kibbeh — A4, cutting — A5.
CAUTION! The operation time should not exceed 5 minutes. A break should not be less than 15 minutes.
Do not put bones, skin, frozen or coarsely cut meat into the meat grinder. It shortens the service life of the appliance and may
lead to its breakage.
Use of reverse function
Use the reverse function if liquid accumulates inside the cutting unit or the meat grinder unit and output product's solid mass
prevents it from flowing.
If the squeezer is in operation at the moment, stop the rotation of the shaft by pressing the ON/OFF button. Then press and
hold down the REV button. The screw will turn backwards moving the foods towards the feed chute port. Release the REV
button in 10-15 seconds and then press the ON/OFF button to resume processing.
Overload protection system
The meat grinder is equipped with an overload protection system of the motor (e. g. if the bone gets into the grinder unit
together with meat).
If the motor is unexpectedly stopped, switch off the meat grinder, press ON/OFF, and disconnect from the power outlet. Clean
the working unit from foods. Press the overload protection button on the bottom of the appliance, then plug in the appliance
and press ON/OFF. If the meat grinder still doesn't work, apply to the service center.
III. CLEANING AND MAINTENANCE
See the recommended methods of cleaning different appliance parts in the table A6.
10
14. Forming part of kebbe attachment
15. Sausage attachment base
16. Forming part of sausage attachment
17. The motor unit with the storage compartment for per-
forated discs
18. Power cord
19. Shredder
20. Fine grater
21. Large grater
22. Cutting unit square-topped pusher
23. Cutting unit
24. Overload protection button
CAUTION! Switch off the appliance and unplug it before disassembling and cleaning.
DO NOT immerse the motor drive unit, plug and power cord in water or keep in running water.
DO NOT use sponges with hard or abrasive surface, abrasive scouring substances and solvents (benzine, ethyl acetate and others).
Let all parts dry at room temperature and natural ventilation.
Store the assembled appliance in a dry, ventilated place away from heating and direct sunlight.
IV. BEFORE CONTACTING SERVICE CENTRE
Problem Possible causes
Power cord is not connected to the appliance and
(or) to the outlet
The appliance does not
Faulty electrical outlet
switch on
Power supply failure
Motor drive stopped
Overload protection activated
during operation
The appliance is overheated during operation
An off-odour appeared
during operation
Some parts of the appliance have protective cover The odour will disappear after few uses
V. PRODUCT WARRANTY
We warrant this product to be free from defects for a period of 2 years from the date of purchase. If the appliance fails to
operate properly within the warranty period and is found to be defective in material or workmanship, we will repair or replace
it free of charge. This warranty comes into force only in case an original warranty service coupon with a serial article number
and an accurate impress of the company of the seller proves the purchase date. This limited warranty does not cover damage
caused by the failure to use this product for its normal purpose or in accordance with the instructions on the proper use and
maintenance of the product, or any kind of repair works. Do not try to disassemble the appliance and keep all package contents.
This warranty does not cover normal wear of the appliance and its parts (filters, bulbs, non-stick coating, gaskets, etc.).
The service life and the applicable product warranty period start on the date of purchase or the date of manufacture (if the
purchase date cannot be established).
You can determine the manufacture date by the serial number located on the identification label on the housing of the appliance.
The serial number consists of 13 digits. 6th and 7th digits of the serial number identify the month, 8th digit the year of manufacture.
The service life of the product, established by the manufacturer is 3 years from the date of purchase, provided that the unit
is used and maintained in accordance with the user manual and applicable technical standards.
Environmentally friendly disposal (WEEE)
The packaging, user manual and the device itself shall be taken to the applicable collection point for the recycling
of electrical and electronic equipment. Do not throw away the electronic waste to help protect the environment.
Old appliances must not be disposed with other household waste but must be collected separately. Municipal
disposal of recyclable wastes is free of charge. The owners of old appliances are required to bring it to a waste
facility centre. With this little extra effort, you can help to ensure that valuable raw materials are recycled and pollutants are
treated as appropriate.
This appliance is labelled in accordance with European Directive 2012/19/EU — concerning used electrical and electronic
appliances (waste electrical and electronic equipment WEEE).
The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU.
Solution
Plug in the appliance
Plug in the appliance to the working outlet
Check the voltage supply. In case of its failure, contact an
authorized organization
Switch off the meat grinder, press ON/OFF, and disconnect
from the power outlet. Clean the working unit from foods. Press
the overload protection button on the bottom of the appliance,
then plug in the appliance and press ON/OFF. If the meat
grinder still doesn't work, apply to the service center
Reduce continuous operation time, increase intervals be-
tween switching