Dolmar AG-3750 Manual De Instrucciones página 7

Remaining battery capacity indication
Battery indicator status
: On : Off : Blinking
015527
Switch action (Fig. 3 & 4)
CAUTION:
• Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.
For continuous operation, pull the switch trigger, push
in the lock button and then release the switch trigger.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
Speed change (Fig. 5)
The maximum air volume can be adjusted just by turning
the adjusting dial. This can be done even while the tool
is running. The dial is marked 1 (lowest) to 6 (highest).
NOTICE:
• The speed adjusting dial can be turned only as far as 6
and back to 1. Do not force it past 6 or 1, or the speed
adjusting function may no longer work.
When working in a high temperature circumstance, the
tool may be stopped because of the overheat protection
system. In that case let the tool cool down. Avoid setting
to speed 6 (highest) in high temperature circumstances.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
Installing the long nozzle (Fig. 6 & 7)
To install the long nozzle:
1. Align the small projection of the housing with the
groove of the long nozzle.
2. Slide in the long nozzle, and turn it clockwise until the
triangle markings on the long nozzle and the housing
meet each other.
The length of the nozzle can be adjusted by changing the
locking position.
Remaining battery
capacity
50% – 100%
20% – 50%
0% – 20%
Charge the battery
Installing the shoulder strap (optional accessory)
(Fig. 8)
Hook the shoulder strap onto the hanger of the tool.
Before use, adjust the length of strap so that it is easy
to work with it.
OPERATION
Blowing (Fig. 9)
CAUTION:
• Do not place the blower on the ground while it is
switched on. Sand or dust may enter from suction inlet,
and they may result in personal injury.
Hold the blower firmly with a hand and perform the
blowing operation by moving it around slowly.
When blowing around a building, a big stone or a
vehicle, direct the nozzle away from them.
When performing an operation in corner, start from the
corner and then move to wide area.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Cleaning (Fig. 10)
From time to time, wipe off the outside of the tool using a
cloth dampened in soapy water.
To maintain product
repairs, any other maintenance or adjustment should
be performed by DOLMAR Authorized Service Centers,
always using DOLMAR replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Dolmar tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Dolmar Service Center.
• Dolmar genuine battery and charger
• Shoulder belt
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN50636:
Sound pressure level (L
Uncertainty (K): 1.8 dB (A)
Sound power level (L
Uncertainty (K): 2.3 dB (A)
Wear ear protection
SAFETY and RELIABILITY,
ENG108-1
): 79.1 dB (A)
pA
): 93.5 dB (A)
WA
7