Olymp LavaSit COMFORT Instrucciones De Montaje página 7

Mounting instructions for electricians:
11. Electrical connection:
Caution:
•
Electrical connections are reserved to
authorized electricans!
•
The safety regulations of the hairdressing trade must be
observed. Installation and operation must be in
accordance with the norm IEC 60364 ...
•
During assembly work the complete system
must be isolated from the power supply and
secured against unintended switch-on!
•
In the wash unit, use only the plug-in connectors
supplied with the appliance and specified in the
mounting instructions!
•
Cables must be so arranged that they are not in the
vicinity or moving parts! Damage or crushing must thus
be prevented!
•
For reasons of mechanical security as well as the
electromagnetic compatibility no cable excess may be
stowed away in the shampoo unit.
Shampoo station with direct connection:
•
The shampoo station must be connected to the
electrical floor outlet by a qualified electrician.
•
Unit with direct connection: shorten the connection
cable and connect it to the floor outlet with less
cable excess.
Mounting instructions for appliance fitters:
Shampoo station with mains cable:
•
The shampoo station is „ready to plug in" and can be
plugged to a wall plug socket by the customer without
the help of an electrician.
•
The power supply cable from the unit must be
arranged so that it is not jammed between the
unit frame and the floor!
•
Do not place any plug socket inside of the unit!
Always route the mains cable outside and plug into a
customer's site plug socket.
•
The wash unit with power supply cable must not be
connected to the power supply using an extension
cable.
•
Arrange the power supply cable so that the plug is
easily accessible and can be isolated from the wall
socket.
•
In case several wash units are to be installed in-line,
the power supply cable must not be connected via
further units.
Comfort MO W+R
GB
Mounting instructions for electricians
and appliance fitters:
Variants for single units:
11.1 Direct connected variant: (Fig. 6)
Caution: This type of connection must only be
made by a qualified electrician!
- Replace plug of power supply cable with the
system plug supplied (Fig. 4)
- Connect power supply cable from the floor to
the system socket supplied (Fig. 4)
- Plug system plug into the system socket and close
safety catch (Fig. 5).
11.2 Mains cable variant: (Fig. 7)
Route the mains cable with plug through the installation
tunnel to the outside.
In-line installation variants:
11.3 In-line installation with direct wiring (Fig. 8)
> Connection see 11.1
11.4 In-line installation with plug/socket (Fig. 9)
> Connection see11.2
Mounting instructions for appliance fitters:
12. Assembly:
12.1 Using a cable tie, hold the 2 pressure hoses (hot + cold)
loosely together.
12.2 Attach front housing (3 + 4):
Push housing components in the reverse order as in fig. 3
onto the column housing (1) and close the magnet
connector.
Attach housing components (3 + 4) via the hexagonal
socket screw inside to the column housing. Check that
housing components fit correctly. Otherwise unscrew the
fasteners and re-align the components, then re-
tighten screws.
12.3 Replace bottom cover of chair (7): press it tightly in
place, first at the rear then at the front.
(velcro fastener)
12.4 Replace and close inspection door (5).
12.5 Place the remote control on the decorative button at
the side of the backrest (holds magnetically).
13. Servicing
13.1 For service work at the electric system first ride out
leg rest. If this is not possible, detach leg rest from front
support (12) by removing 4 allen screws. Then loosen
cover at the bottom side of the chair (7):
- loosen 2 screws at front side
- loosen Velcro connection carefully
- swing cover downwards
13.2 For service work at the massage mechanics the backrest
upholstery as well as the backrest cover can be
removed:
- Pull backrest upholstery (8) upwards
- Pull back backrest cover rearwards (9)
(Velcro fastening)