Husqvarna S 138i Manual De Usuario página 14

LED lights
All LEDs are lit
LED 1, LED 2, LED 3 are
lit
LED 1, LED 2 are lit
LED 1 is lit
LED 1 flashes
To charge the battery
Charge the battery before the first use. The battery is
only 30% charged when supplied to the customer.
Note:
The battery charger must be connected to the
voltage and frequency specified on the rating plate.
The battery does not charge if the battery temperature
is above 50°C. The battery charger decreases the
temperature of the battery before it starts to charge.
1. Connect one end of the power cord for the battery
charger into the socket of the battery charger.
2. Connect the other end of the power cord for the
battery charger in an grounded mains socket. The
LED on the battery charger flashes green one time.
(Fig. 30)
3. Put the battery in the battery charger. The green
light on the charger comes on when the battery is
correctly connected to the battery charger. (Fig. 31)
4. When all LEDs on the battery have come on the
battery is fully charged. Charge the battery for
maximum 24 hours.
5. To disconnect the battery charger from the mains
socket, pull the plug, not the power cord.
6. Remove the battery from the battery charger.
To start the product
1. Put a charged battery in battery compartment
number 1 below the battery lid. For longer operation
time, put a second charged battery in battery
compartment number 2.
2. Turn the safety key to 1. (Fig. 32)
3. Stay behind the product.
4. Press the ON/OFF button (A) on the control panel
and the green LED (B) comes on. (Fig. 33)
5. Loosen the start inhibitor. (Fig. 34)
6. Push the motor brake handle in the direction of the
handlebar. (Fig. 35)
14
Battery status
Fully charged (76-100%)
The battery is 51%-75%
charged
The battery is 26%-50%
charged
The battery is 6%-25%
charged.
The battery is 0%-5%
charged.
To use the SavE function
The product has a battery saving function (SavE) that
gives longer operation time.
1. Press the SavE button (A) to start the function. The
green LED comes on. (Fig. 36)
2. Press the SavE button again to stop the function.
The green LED (B) goes out.
High load function
When the product cuts long or wet grass, the motor
automatically increases rpm. The motor goes back to
standard mode when high load is not necessary.
Motor stalling
During operation, the blade and motor can temporarily
stop because of obstacles such as grass blockage
below the cutting cover. If this occurs and you keep the
motor brake handle pushed down, the product restarts
automatically. If the product does not restart in 5-10
seconds, it can be necessary to clean below the cutting
To clean the product on page 15 .
cover. Refer to
WARNING:
product tries to restart automatically for 5-10
seconds. Wait for a minimum of 15 seconds
before you do a check of the cutting cover.
WARNING:
cutting cover, release the motor brake
handle, turn the safety key to 0, remove
the battery and wait for a minimum of
5 seconds. There is a risk of injury if
the obstacle is removed and the product
accidentally starts.
To stop the product
The product stops automatically if you do not operate it
for 10 minutes. Never let the product stay out of view
with the motor started. Stop the motor, turn the safety
key to 0 and remove the battery. Make sure that the
detatcher equipment does not rotate.
1. Release the motor brake handle to stop the motor.
(Fig. 37)
2. Press the ON/OFF button (A) on the control panel
and the green LED (B) goes out. (Fig. 33)
3. Open the battery lid and turn the safety key to 0.
(Fig. 38)
4. To remove the battery, press the 2 release buttons
at the same time and pull out the battery. (Fig. 39)
5. Charge the battery if it is weak. For more
To charge the battery on page 14 .
information, see
If the motor stops, the
Before a check of the
937 - 008 - 13.11.2023