Publicidad
Idiomas disponibles
Idiomas disponibles
Toapply detergent fellow these steps:
1.
ReviewProjectPro _'nozzleand HydroFoam
TM
launcheruse.
2.
Prepare HydroFoam
TM
wash according to instructions on
the bottle or prepare detergentsolution as required by job.
3.
Mace smaii fiiter end of detergent siphoning tube into
detergent container=
NOTE:Make sure the fiiter is fully submerged in detergent
while applying detergent=
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube=
Wheninserting thefilter intoa detergent solutionbottle,routethe
tubesoasto keepitfrom inadvertently contacting thehot rnuffler.
4.
Make sure HydroFoam
TM
Launcher is installed.
NOTE:Detergentcannot be appiied with the high pressure
nozzles (Yeliow, Orange or Red).
5.
Make sure garden hose is connected to water iniet.
Checkthat high pressure hose is connected to spray gun
and pump. Turn on water.
NOTICE
You must attach all hoses before you start the engine=
Startingthe enginewithoutall the hosesconnected andwithout
the waterturnedONwill damage tbe pump.
Darnage to equipment r esultingfrom failureto follow this
instruction will void warranty.
6= Start engine foiiowing instructions How to Start Your
Pressure Washer=
7= Appiy HydroFoam
TM
wash to a dry surface, starting at
lower portion of area to be washed and work upward,
using iong, even, overlapping strokes=
NOTE:To prevent water spotting on vehicies, work in a
shaded area and aliow surfaces to coot before beginning.
8= Aiiow HydroFoam
TM
wash to soak in between
3-5 minutes before washing and rinsing. Reappiy as
needed to prevent surface from drying. DO NOTaiiow
HydroFoam
TM
wash to dry on (prevents streaking).
For best results, scrub the HydroFoam
TM
wash covered
surface to help remove stubborn dirt, grime and stains. For
vehicies, use a soft car wash brush or mitt. For decking,
siding and concrete, use a brush appropriate for the type of
surface being cleaned=
J_IPORTANT: You must flush the detergent siphoning system
after each use by piacingthe fiiter into a bucket of clean water,
then run the pressure washer in low pressure for 1-2 minutes.
Pressure Washer Rinsing
After NydroFoam
TM
wash is applied, eceor the sorfaoeand rinoe
it cleanas fellows:
1.
Remove HydroFoam
TM
Launcher from nozzle extension.
2.
Seiect and instaii desired ProjectPro_ nozzle,as
described in How to Use ProjeotPrd"__ N ozzleSystem.
3.
Keepspray gun a safe distance from spray surface.
WARNING
Kickback from spray gun can cause you to fail=
o Operate pressure washerfrom a stablesurface.
o Beextremely carefulif you mustusetbe pressure wasberfrom
a ladder,scaffolding,or anyotbersimilarlocation.
* Firmlygraspspraygun with both handswbenusing high
pressure sprayto avoidiniurywhenspraygun kicks back.
4= Appty a high pressure spray to a smati area and then
check the surface for damage=If no damage, proceed to
step 5=
Start at top of area to be rinsed, working down with
same overlapping strokes used for cleaning=
Cteauiug getergeut $ipheuiug Tube
If you used the detergent siphoning tube, you must flush it
with ciean water before stopping the engine.
1= Piacedetergent siphoning tube/filter in a bucket full of
clean water.
.
3=
,
5=
Remove high pressure nozzie from nozzteextension.
Select and instaii btack detergent nozzJefoiiowing
instructions How to Use ProjectPrd_ Nozzle System.
Ftushfor 1-2 minutes.
Shut off engine foiiowing instructions How to Stop
Pressure Washerand turn off water suppiy.
6= ALWAYS point spray gun in a safe direction, press red
button and squeezespray gun trigger to reiease retained
high water pressure=
iMPORTANT:Spray gun traps high water pressure, even
when engine is stopped and water is disconnected.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, ieading to serious injupj and
}ossibie amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.
o Keephigh pressurehoseconnected to reelandspraygun while
systemis pressurized.
• ALWAYS pointspraygun in safedirection,pressred button
and squeeze spraygun trigger,to releasehigh pressure, e very
time youstop engine.
Automatic
Cool gewu System {Thermal lielief}
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circuiating water in the pump can reach temperatures above
125%=The system engagesto cool the pump by discharging
the warm water onto the groond=
16
Publicidad
