Rupes PL824V Manual De Instrucciones página 5

librettoPL824 30-03-2007
PL824V PLANER
(See figures in pages 24, 25, 26, 27)
1. FOR YOUR SAFETY
WARNING! Before using the planer, model
PL824V, carefully read the GENERAL SAFETY
PAMPHLET included with the machine's docu-
mentation.
Before connecting the machine, ensure that the
supply voltage matches that which is shown on
the identification plate.
Use safety goggles when working with this
machine.
Keep your hands away from the cutting area.
Always guide the planer firmly with both hands.
Avoid planing nails. Inspect the work surface
before planing it.
Always remove the plug from the mains socket
before carrying out any maintenance work with
the machine.
Always use original RUPES blades. Never use
blades that are dull, defective or in bad condition.
Always use the original RUPES blade holders
and blade supports mounted on the machine. If
necessary, replace them with original RUPES
parts.
Operate the planer with the rest shoe.
Wait until the machine has come to a complete
halt before releasing or moving it.
Wear earplugs when using the machine (see
chapter 12)
2. SPECIFICATIONS
Input power
Motor
No load speed
Cuts per minute
Equivalent measured continuous
acoustic pressure level A
Normal level ofvi brations (hand-arm)
Cutting width
Cutting depth
Rabbeting depth
Weight
3. STANDARD EQUIPMENT
Inside the box you will find the following compo-
nents:
1. Planer PL824V
2. Lateral fence
3. Spanner for fixing blades (a/f 8)
14:57 Pagina 5
English
750W
50/60Hz
13,000/min
26,000
84 dB(A)
<2.5m/s
82mm
0-4mm
25mm
3.750 Kg
4. GENERAL DESCRIPTION
The Planer PL824V comes equipped with:
• Reversible HM blades
• Cutting regulator with automatic locking, for pla-
ner width of up to 4 mm
• Regulable lateral shoe for rebate depth of up to
25 mm
• Sliding horizontal guide for planing overlaps of
0-1 mm
• Lateral fence for work to be done on the edge
of the workpiece
• Collector outlet can be placed on the right or left
side
• Safety switch A (Fig. 1) with inverted locking B
(Fig. 1) for right-handed or left-handed users that
prevents the machine from starting accidentally
• Lateral blade guard
• Concealable rest shoe, to prevent the blade
from coming into contact with the workpiece once
the planer is switched off
• Blade-holder equipped with mechanical brake
system.
5. CUTTING CONTROL
Cutting depth
Turning knob C (Fig. 2) clockwise regulates cu
tting. The knob's locking screws enable planing
width adjustment to be carried out in 0.2-mm
steps. Maximum cutting depth is 4 mm.
Planing of rebates and overlaps
Rebate depth is set by means of the parallel shoe
D (Fig. 2). The shoe is placed at the desired
height by simultaneously pressing and turning
the knob E. When the knob is released the shoe
remains fixed in the desired position. Maximum
rebate depth is 25 mm.
The planer PL824V enables one to plane over-
laps (Fig. 3), thanks to its sliding guide F (Fig. 3).
This permits cutting from 0-1 mm by means of
the regulation of the screw G (Fig. 3, 4). Always
remember to have a good support for the planer
base.
2
Lateral fence
The lateral fence H (Fig. 2) enables you to posi-
tion the planer for work to be done on the side of
the workpiece. To attach it, push lever I (Fig. 2)
and slide the square by means of the hole J (Fig.
4) to the desired measurement. When the lever I
is released, the parallel square will remain locked
in this position. If need be, a more precise regu-
lation can be obtained using the bracket K (Fig.
2).
Chamfering the edges
To chamfer the edges of a workpiece quickly and
5