Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
52WH244DP
52WH244DPF
S568N244SSWHP
S568N244SSBZP
62BK244CBK
62BK244CCN
62BK244CMP
S468244SS
52WH344DP
52WH344DPF
S568N344SSBZP
S568N344SSSNP
S468344SS
52WH254DP
52WH254DPF
52WH304DP
52WH304DPF
* Visit www.rangairemfg.com/products using the model number to see additional dimensions and features in the Product Specifications or Jensen Medicine Cabinet catalog.
PREPARATION
1. Carefully remove packaging materials. Hardware, shelves, and
door are located within the various packing materials. Place
hardware packages, shelves, and door aside until needed.
NOTE:
For ease of installation, the assistance of an additional
person is recommended.
INSTALLATION
1. Determine the desired location for the cabinet on the wall.
Mark wall to show wall opening width and height (see chart
above). Generally, the recommended height of bath
cabinets is 64" from the finished floor to the center of the
cabinet. (Fig. 1) However, height may be adjusted to
individual preference.
2. The cabinet may be mounted with door opening to the right
or left side. Rotate the cabinet, top to bottom, to reverse
the door opening direction.
NOTE:
The rough wall opening must be free of obstructions. If
wall studs, plumbing, or electrical lines interfere with
the rough wall opening they must be removed /
relocated. This must be done in accordance with local
and national codes and it is recommended that the
services of a plumber or electrician be obtained.
3. Cut wall opening, being careful not to damage the surrounding
wall surface or any existing wiring or pipes that may be behind
the wall section being removed. Insert framing to support all wall
edges.
4. Insert mounting screws into the plastic bases (Fig. 2).
5. Level and plumb cabinet in center of wall opening. Use shims as
necessary. Use 4 mounting screws to attach cabinet to wall
studs (Fig. 3). Tighten screws until they are flush with the
housing. DO NOT OVER TIGHTEN. Over tightening may bend
housing sides and prevent proper shelf installation.
Do not use nails to attach the cabinet.
NOTE:
6. Snap the screw covers over the screw bases (Fig. 4).
1
Model*
72SS244D
S568N244SSSNP
62BK244CCY
72SS344D
S568N344SSWHP
INSTALLATION INSTRUCTIONS
FOR RECESSED MOUNTED CABINET
(SURFACE MOUNT APPLICATIONS
REQUIRE A SURFACE MOUNT KIT)
Wall Opening
W
H
14¼
24
14¼
34
19¼
24
23¼
29
Fig. 1
Approx.
64" to the
floor
Fig. 2
Insert
screw
through
clear
plastic
base
Fig. 3
Mounting
screws
D
4
4
4
4
H
D
W
Fig. 4
Cover
Screw
Base
Snap on cover
Mounting
screw into
mounting
hole
628056_A
Publicidad
Resumen de contenidos para Jensen 52WH244DP
- Página 1 19¼ 52WH304DP 52WH304DPF 23¼ * Visit www.rangairemfg.com/products using the model number to see additional dimensions and features in the Product Specifications or Jensen Medicine Cabinet catalog. PREPARATION Fig. 1 1. Carefully remove packaging materials. Hardware, shelves, and door are located within the various packing materials. Place hardware packages, shelves, and door aside until needed.
- Página 2 DOOR INSTALLATION Fig. 5 1. Remove hinges and screws from hinge hardware bag. 2. Become familiar with the hinge attachment and removal process prior to mounting the hinges (Fig 5). Hinge mounting brackets are attached to the housing side. 3. Mount hinges to the door (Fig. 6). Secure with screws provided.
- Página 3 INSTALLING 125° LIMIT TO 170° HINGE Fig. 10 1. Open cabinet door 90° from closed. Locate the oval / oblong slots located top and bottom of the hinge between the second and third knuckle. Hook one end of limit clip into the upper slot.
- Página 4 MIRROR CARE Use only clean warm water and a clean, soft, lint- free cloth. DO NOT USE cleaners that contain solutions of For assistance contact Rangaire Manufacturing ammonia, vinegar, or chlorine. Customer Service: DO NOT USE powdered cleansers or steel wool. 1-800-325-8351 ...
- Página 5 73,7 cm 10,2 cm *Visite www.rangairemfg.com/products y utiliza el número de modelo para ver la dimensiones y características adicionales en la especificaciones del producto o en el catálogo Jensen Medicine Cabinet. PREPARACIÓN Retire cuidadosamente los materiales de empaquetamiento. Los accesorios, Fig.
- Página 6 INSTALACIÓN DE LA PUERTA Fig. 5 1. Retire las bisagras y tornillos de la bolsa con los accesorios para bisagras. La barra en la 2. Familiarícese con el proceso de colocación y desmontaje de parte inferior de bisagras antes de montar las bisagras (Fig. 5). Los soportes la bisagra se Vista de montaje de las bisagras están colocados en el lateral de la...
- Página 7 INSTALANDO EL LIMITE DE 125° A LA BISAGRA DE 170° Fig. 10 . Abra la puerta del gabinete 90° antes de cerrar. Localice los espacios óvalos / oblongos ubicados arriba y abajo de la bisagra entre el segundo y tercer nudillo. Enganche un lado del broche de limite en el espacio de arriba.
- Página 8 CUIDADO DEL ESPEJO Utilice solo agua tibia y limpia y un paño limpio y suave sin pelusas. NO UTILICE productos de limpieza que contengan soluciones de amoníaco, vinagre o cloro. Si usted necesita ayuda Rangaire Manufacturing NO UTILICE limpiadores en polvo o lana de Customer Service: acero.