Metabo PK 255 Manual Del Usuario página 11

XA0065E2.fm
3
Note:
Starting June 1, 2006 the valid
Technical Specifications are shown in
the Supplementary Sheet, and the appli-
cable Wiring Diagram is shown in the
Spare Parts List.
1. Please Read First!
This Supplementary Sheet has been
written to make it easier for you, the
operator, to operate this machine safely.
It should be used as follows:
− Read the Operating Instructions and
this Supplementary Sheet before
using the machine. Pay special
attention to the safety information.
− This
Supplementary
intented for persons with a basic
technical knowledge regarding the
operation of a machine like the one
described herein.
persons are strongly advised to
seek competent advise and guid-
ance from an experienced person
before operating this machine.
− Keep all documents supplied with
this machine for future reference.
Retain proof of purchase in case of
warranty claims.
− If you lend or sell this machine be
sure to have these instructions go
with it.
− The manufacturer does not assume
liability for personal injury or dam-
age resulting from the non-observ-
ance of any operating or safety
instructions given in the Operating
Instructions or this Supplementary
Sheet.
Information in this Supplementary Sheet
is denoted as under:
Danger!
Risk of personal injury or
environmental damage.
Risk of electric shock!
Risk of personal injury
by electric shock.
Entanglement hazard!
Risk of personal injury
by body parts or clothing
being drawn
rotating saw blade.
Danger!
Do not reach into the
machine!
Betriebsanleitung
Note:
Positioning of sliding carriage on PK
saw.
Sheet is
Inexperienced
− At times numbers are used in illus-
trations (1, 2, 3, ...). These numbers
− indicate component parts;
− are consecutively numbered;
− correspond wit the number(s) in
− Numbered steps must be carried out
in sequence.
− Instructions which can be carried
out in any order are indicated by a
bullet point (•).
− Listings are indicated by a dash (–).
2. Safety Instructions
2.1
This machine is intended to rip and
crosscut grown timber, faced boards,
chip board and wood-core plywood
sheets, and similar wood-derived materi-
als.
Do not cut round stock without suitable
jigs or fixtures. The rotating saw blade
could turn the workpiece.
Any other use is considered to be not as
specified and not allowed. The manufac-
turer is not liable for any damage caused
by unspecified use.
Modification of the machine or use of
parts not approved by the manufacturer
into the
can cause unforeseeable damage!
2.2
•
When using this machine, observe
the following safety instructions to
exclude the risk of personal injury or
material damage.
DEUTSCH
Caution!
Risk of material damage.
Note:
Additional information.
brackets (1), (2), (3) ... in the
neighbouring text.
Specified Conditions of
Use
General Safety Instruc-
tions
ENGLISH
•
Please also observe the special
safety instructions in the respective
chapters.
•
Where applicable, follow the legal
directives or regulations for the pre-
vention of accidents pertaining to
the use of circular saws.
•
When turning OFF:
Check if saw blade is post-running
for more than 10 seconds; if more
than 10 seconds,
replaced by a qualified electrician.
A
General hazards!
•
Keep your work area tidy – a messy
work area invites accidents.
•
Be alert. Know what you are doing.
Set out to work with reason. Do not
operate machine while under the
influence of drugs, alcohol or medi-
cation.
•
Consider environmental conditions:
keep work area well lighted.
•
Prevent adverse body positions.
Ensure firm footing and keep your
balance at all times.
•
Use suitable workpiece supports
when cutting long stock.
•
Use auxiliary devices to cut wide
panels safely.
•
Depending on the job on hand, use
these auxiliary devices:
− Table Extension (optional acces-
sory) – if workpieces would fall off
the table after cutting.
•
Wedges may only be cut using a
wedge cutting jig, adapted to the
desired wedge thickness, length,
and taper:
− Install riving knife and blade
guard.
With your right hand push the wedge
cutting jig against the rip fence, while at
the same time feed it into the saw blade.
Secure workpiece with your left hand.
•
Do not operate the machine near
inflammable liquids or gases.
•
The saw shall only be started and
operated by persons familiar with
circular saws and who are at any
time aware of the dangers associ-
ated with the operation of such
machine.
Persons under 18 years of age shall
use this machine only in the course
of their vocational training, under the
supervision of an instructor.
•
Keep bystanders, particularly chil-
dren, out of the danger zone. Do not
permit other persons to touch the
machine or power cable while it is
running.
•
Do not overload machine – use it
only within the performance range it
have motor
11