GE SmartWater GXWH35F Instrucciones De Instalación

INSTALLATION INSTRUCTIONS
Heavy Duty Water Filtration System--GXWH35F (filters not included)
SAFETY PRECAUTIONS
• Check with your state and local public works department for
phnnbing and sanitation codes. You must tollow these guidelines
as you install the Heavv Due,' Water Filtration System. Using a
qualified installer is recommended.
• Be sure tile water supply confl)m_s with tile
Performance Data.
If tile water supply conditions are unknown, contact your
mulficipal _;_teI" colni)an >
^.. WARNING: D ,, ,l e
microbiologically unsafe or (d unknown quality without adequate
disintecfion before or after the system.
• It is highly recommended that a water shut-off wflve be placed
directly upstream ot your household filteI:
PROPER INSTALLATION
This Heavy Duty Water Filtration System must be properly installed and located in accordance with the Installation Instructions
before it is used.
• Checkwith yeurlocalpublic works departmentferplumbing c odes.
You mustfollow theirguidesas youinstafltheHeavyDutyWater
FiltrationSystem.
• Usethe HeavyDutyWaterFiltrationSystem on a potable,safe-to-
drink,homeCOLDwatersupply only.Thefilter cartridgewill not
purifywateror make unsafewatersafe todrink.DONOTuseon
HOTwater (IO0°F max).
• Protectthe HeavyDuty WaterFiltrationSystem andpipingfrom
freezing.Waterfreezingin thesystemwill damageit.
• YourHeavyDutyWaterFiltration Systemwill withstand up to 100 psi
waterpressure, f f yourhousewatersupply pressure is higherthan
100psi during the day(itmayreach higherlevelsat night),install
a pressure reducingvalvebeforethesystem is installed.
• Do not install on HOT WATER.Tile temperature of tile water
supply to tile Heavv Dull,' Water Filtration System m list be
between tile minimum of 40°E and tile maximum ot 100°E
See tile Performance Data secdon.
• Do notinstall the Heavv Dull,' _._teI" Filtration System using
copper solder fittings. The heat fi'om the soldering process
will damage the unit.
A WARNING: ...,ed p.,,, l'ackaging
,
matei_Jal alter installation. Slnall parts ren_ailfing alter installation
could be a choke hazard.
• Do net install filter in an outside location or anywhere it will be
exposed to sunlight.
REQUIRED TOOLS AND ACCESSORIES
FOR INSTALLATION
• 2 A(!justable wrenches
• Pipe cutter
• Ruler or tape measure
• Cordless drill
• File
• Emery paper
• Screwdriver
• Additional installation parts may be required:
" 2 fittings to connect household i)lumbing to l" female NPTF
threads on filter housing. Installation Kit available to c(mnect
to 3/4" COl)per plmnbing:
-- GE Part/Retail Part (HDKIT)
(Not pedom_ance tested or certified by NSE)
" UI, Approved
grounding clamps and 6-gauge COl)per
grounding wire--Installation Kit available:
-- GE Part/Retail Part (HDKIT)
(Not pei-tbm/ance tested or certified by NSE)
" Teflon Tape
Optionai accessories areavaiiabie (Wsa, MasterCard or Discover cards
accepted) byvMtingour Website atge.com or fromParts andAccessor&s,
caii800.626.2002 (US) or 8012 663,6060 ( Canada).
CONTENTS INCLUDED WITH PRODUCT
• Filter housing and head
• Product literature
• Calfister wrench
• Timer and batteries
• Mounting bracket
• 4 Hex-head scre_:s and 4 Hex washe>head scre_:s
GXWH35Fis Tested and Certified by NSF International
against NSF/ANSI Standard 42 with cartridge FXHTC
for the reduction of Chlorine, Taste and Odor.
184D1061P002 (0:4-a)6,lR) 49-50201
ge.com
(;ENERAI, EI£CTRIC COMPANY, Appliance Park, i,ouisville, KY40225
1