Chasing Remote Controller 3 Manual Del Usuario página 3

CHASING Remote Controller 3
Manual
EN V1.0
The CHASING Remote Controller 3 had integrated communication and control. It
connects directly to the drone via the included tether and connects wirelessly to your
mobile phone/tablet via Wi-Fi. And your mobile phone/tablet also can be directly
connected to the remote control through the Type-C cable. It allows the drone to
display a live video feed on your phone/tablet, which enables users to control the
drone in real-time. The remote controller 's HDMI output can also be used to display a
live video feed to a larger screen.
9
5
2
4
3
1. Power switch: Turns controller on/off
2. Power Indicator: Green (High power), Blue
(Medium power), Red (Low power)
3. Wi-Fi switch button: Short press to switch
5Ghz/2.4Ghz Wi-Fi
4. Signal Indicator:
2.4G : 2.4Ghz Wi-Fi indicator, always on
when working
5G: 5Ghz Wi-Fi indicator, always on when
working
ROV(drone): Indicates the communication
status between the controller and the
drone
(Steady light indicates successful
connection;
Blinking light indicates disconnection.)
5. One-key reset: Short press to reposition
the ROV return to a horizontal state/
Long press to switch control mode
6. Unlock: Unlock/Lock，current state of
the Thruster will show on the App
7. Led Control: On/off led light (0%50%100%)
8. Safety Buckle: Can be used with a safety rope
03
17
18
9
8
15
7
14
6
10
1
12
9. Control Sticks: Used to control the naviga-
tion of the ROV
10.Robotic Arm Control: Press and hold to
enable/disable the grabber claw function;
press to change the floodlight brightness level
11. Photo/Video: Short press to take photos,
long press to start / end recording video
12. Right Angel Adjustment: Adjust the roll
angle or control the opening and closing
of the grabber claw
13. Left Angel Adjustment: Adjust the pitch angle
14. Type-c Port: Direct connection with mobile
phone/tablet device
15. HDMI Socket: 1080P HD image real-time
output
16. Tether Connection Socket/Charging socket
17. Phone/Tablet Clamp: Used to attach
phone/tablet mount to mounting bracket
18. Clamp Button: Pull apart the two ends and
put in the phone/tablet, then press this
button to tighten
Handle indicators introduction
Battery：
Red：10%↓ Red light flashes quickly；10-29% Red light always on.
Blue：30-69% Blue light always on；
Green：70-100% Green light always on;
Signal Indicator：
2.4G：2.4Ghz Wi-Fi indicator，always on when working.
5G：5Ghz Wi-Fi indicator，always on when working.
ROV：Indicates the communication status between the controller and the ROV (Steady
light indicates successful connection, Blinking light indicates disconnection.)
Gesture back Button：The blue light is always on when the ROV is in a non-horizontal position.
Unlock Button：
Locking: No lights； Unlocking: Blue light on.
Led Control Button：
Bright light: Blue light always on; Low light: Blue light flash; No light: Blue light off.
Connection
16
11
Start (turn on) the ROV
1
13
a. Please first connect the remote controller with the ROV through the tether.
b. Turn on the remote controller power button.
c. A few seconds later, the remote controller' s indicator lights up, 5G or 2.4G light will be
always on. And the ROV sounds tow self-test sounds.
Connect remote controller to your phone/tablet
2
Method 1： USB Direct Cable Connection
Choose an appropriate remote controller cable based on
the type of mobile device. A Lightning connector cable,
micro USB cable, and TYPE-C cable are included in the
packaging. Connect the end of the cable with the mobile
phone logo to the mobile device.
Note:
* It is recommended to use this kind of way to connect
mobile phone/tablet and remote controller.
* For iOS users, select "Auto" for IP address configuration.
* If the Android device has a "USB OTG" switch, you need
to turn it on.
* If the connection fails, please try to turn off your phone's
Wi-Fi and mobile network. If still fails, it may be a phone/
tablet compatibility problem. Please select method 2 :
Wi-Fi connection.
* The remote controller type-c port and attached remote
controller cables do not support charging.
EN
6:27 89%
USB 10/100 LAN
Ethernet
IPV4 ADDRESS
Configure IP
Automatic
IP Address xxxxxxxxxx
192.168.1.20
Subnet Mask
255.255.255.0
xxxxxxxxxx
04