Publicidad
Idiomas disponibles
Idiomas disponibles
OWNER'S MANUAL | USING YOUR BLACKSTONE
IGNITIoN INSTRUCTIoNS
1. CHECK VALVES
Turn knob to oFF position�
STEP 01
Push in knob and release� Knob should spring back�
STEP 02
If knobs do NoT
If knobs
do NoT spring back, replace valve assembly before using appliance.
spring back, replace valve assembly before using appliance.
Rotate knob to loW then turn back to oFF� Knob should
STEP 03
turn smoothly�
If burner does not ignite with open gas supply valve, gas
will continue to flow out of burner and could accidentally/
inadvertently ignite with risk of injury.
Ensure gas is o at the supply shut o valve before checking
appliance valves.
3. ALWAYS CHECK BURNER FLAME BEFORE USE.
light burners and rotate knobs from HIGH to loW�
STEP 01
look below the cooking surface to view burners� When knob
STEP 02
is at HIGH, flames should be larger than when knob is at loW�
HEALTHY FLAME PATTERN
❶ ❶
❷ ❷
❸ ❸
❶ ❶
Flickers of yellow color.
Flickers of yellow color.
❷ ❷
dark blue color.
dark blue color.
❸ ❸
Vibrant blue.
Vibrant blue.
12
3. ALWAYS CHECK BURNER FLAME BEFORE USE.
WARNING
YELLOW OR IRREGULAR
If there is a sudden drop or low
If there is a sudden drop or low
flame issue, please reference the
flame issue, please reference the
Troubleshooting chapter.
Troubleshooting chapter.
2. ELECTRIC IGNITION
2. BATTERY POWERED IGNITION
do NoT lean over the appliance while lighting�
do NoT lean over the appliance while lighting�
Make sure the appliance is plugged in�
Insert one (1) AA
STEP 01
Press the oN button�
STEP 01
battery (not included) under the
(optional: Turn the dimmer
ignitor button�
until it clicks to turn off the
Screw the button into place over
puddle lights�)
the positive terminal�
STEP 02
STEP 02
❶ ❶ Turn the control knob to oFF�
❶ ❶ Push the control knob in to
start gas flowing� (WHITE)
Turn gas oN by turning the gas
❷ ❷ Turn the control knob
cylinder handwheel counter-
counter-clockwise to activate the
clockwise 1 to 3 turns�
starter� (FLASHING BLUE)
❸ ❸ Check flame and adjust
STEP 03
the temperature to desired
❷ ❷ Push and hold the ignitor button�
level� (ORANGE)
❸ ❸ Push and turn the control knob counter-clockwise to HIGH�
(Release the ignitor button when the burner lights�)
Note: If the magnet in the knob is disconnected, the indicator light
❹ ❹ Adjust the temperature to desired level�
will be orange� If the knob arrow is facing UP, gas is not flowing�
❶ ❶
❸ ❸
❹ ❹
IF IGNITION DOES NOT OCCUR IN 5 SECONDS:
Turn the burner control knob oFF�
STEP 01
Wait 5 minutes�
STEP 02
Repeat the lighting procedure�
STEP 03
If burner does not ignite, please reference the Troubleshooting chapter.
If burner does not ignite, please reference the Troubleshooting chapter.
IF IGNITION DOES NOT OCCUR IN 5 SECONDS:
Model: 6028
❶ ❶
1 to 3 turns
1 to 3 turns
❷ ❷
❸ ❸
❷ ❷
BLACKSTONEPRODUCTS.COM/SUPPORT
Publicidad
