Reset To Factory Defaults; Other.features; Night View; Battery - JabloCom EYE-02 Instrucciones De Uso

4.5 Reset to factory defaults

If necessary, the EYE-02 camera can be RESET to the factory default settings following this guide:
All user settings, contacts and events will be deleted! The memory card will be formatted , Re-
mote Access Password will be set to 0000 and Configuration Password will be erased. Events
and files downloaded into the JabloTool DESKTOP software will remain in the PC.
• Switch off the camera, remove the battery.
• Wait at least 10 seconds.
• Press the power button and while holding it, carry out the following steps.
• Insert the battery.
• Within 10 seconds, connect the AC power adaptor.
• The camera starts emitting fast beeps.
• Wait until the camera makes 3 longer beeps and both LEDs (R+G) start flashing. Release the power button.
• The camera resets and restarts in ENROLL mode.
Reset to factory defaults can be also done by using JabloTool software application.
5. OTHER FEATURES

5.1 Night View

The EYE-02 camera is equipped with a Night View function, which allows infra-red spectrum photos to be taken.
The EYE-02 camera has a built-in infrared LED lamp, which can illuminate the scene by non-visible infrared light.
Although the human eye cannot see this type of light, the camera chip can take a picture using this spectrum.
The infra lamp illumination is activated automatically when a snapshot is requested and the level of ambient light is
too low.
Objects which reflect IR light might have unrealistic colours on daytime pictures. The color
most affected is the green of plants (trees, grass) as they reflect a high amount of IR light.
Also some parts of black (dark) clothing can look light grey.
The night scene may be overexposed by the IR lamp reflecting off objects located close by. In such cases,
the internal IR lamp should be disabled in the camera configuration and an external IR lamp should be
used instead. For more information about IR illumination see application notes on www.jablocom.com/
download .

5.2 Battery

The EYE-02 camera has an internal backup Li-Ion battery, which allows operation to continue if AC power is lost. If
used in any of the predefined profiles, the backup battery allows the camera to operate for approximately 24 hours.
Any individual sensor configuration may shorten this period accordingly.
In case of active MIP sensor, the backup time may be as short as 40% of the original value. If an IR light is used at the
same time during AC failure, the backup time may drop to 20%.
Please note that each item of network communication will shorten the backup time rapidly, especially if the camera is
operating in an area with poor network coverage. Using the device with a 3G network may also significantly decrease
battery backup time!
The current state of how much your battery is charged can be checked anytime via JabloTool web
interface www.jablotool.com or by using JabloTool desktop software.
• Battery mode
In certain cases, for example when used in locations where AC power is not available, the duration of battery operati-
on may need to be extended. In such cases, you may use the special BATTERY mode.
When in the BATTERY mode, the EYE-02 camera dramatically reduces its power consumption in WATCH. It logs out
of the GSM network, switches off the short range radio receiver and switches on the motion-in-picture detector only
after a WAKE-UP. This means that the EYE-02 camera, while in the BATTERY mode, cannot be reached by calls or
by SMS commands. Additionally, the external detectors and remote controls cannot be used in BATTERY mode.
The EYE-02 camera keeps all the internal detectors working and reports all events as in NORMAL mode. After an
alarm, the EYE-02 camera switches on the radio and logs onto the GSM network for 2 minutes. It reacts to calls, SMS
commands and remote controls during these 2 minutes only.
A fully charged battery can operate the EYE-02 camera in the BATTERY mode for up to 30 days.
For information on how to power EYE-02 from a solar panel, see application notes
on www.jablocom.com/download
EYE-02.ENG.MAN.User_Manual.23.C
- 15 -
EN
ES
DE
FR
NO
FI