Publicidad
Idiomas disponibles
Idiomas disponibles
Beverage Center Shelves
Remove and replace the shelves:
1. Remove the shelf by lifting up the front and pulling it out of
the shelf slots.
2. Replace the shelf by inserting it into the shelf slots and
pushing it toward the back of the compartment.
Important information to know about glass
shelves and covers:
Do not clean glass shelves or covers with warm water
when they are cold. Shelves and covers may break if
exposed to sudden temperature changes or impact, such
as bumping. Tempered glass is designed to shatter into
many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use both hands when
removing them to avoid dropping.
CARE AND CLEANING
Explosion Hazard
Risk of fire or explosion.
Flammable refrigerant used.
Do not use mechanical devices to defrost refrigerator.
Do not puncture refrigerant tubing.
Clean the beverage center once a month to avoid buildup of
odors. Wipe up spills immediately.
To clean your Beverage Center:
1. Unplug beverage center or disconnect power.
2. Empty and remove all shelves and racks from inside the
beverage center.
3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and
a mild detergent in warm water.
To avoid damaging wooden tines and trim pieces, wipe them
off with a clean sponge or soft cloth and warm water. Do not
use detergent or immerse the entire rack into water when
cleaning.
Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, fl ammable fl uids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior and
door liners or gaskets. Do not use paper towels, scouring
pads, or other harsh cleaning tools.
These can scratch or damage materials.
10
Manual W11515229B - BC-Ingles.indd 10
Manual W11515229B - BC-Ingles.indd 10
Cleaning
To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda [2 tbs to 1 qt (26 g
to 0.95 L) of water].
4. Wash stainless steel and painted metal exteriors with a
clean sponge or soft cloth and a mild detergent in warm
water. Do not use abrasive or harsh cleaners, or cleaners
containing chlorine. These can scratch or damage
materials. Dry immediately with a soft, dry cloth to absorb
any remaining water.
NOTE: To keep your stainless steel beverage center
looking like new and to remove minor scuffs or marks, it is
recommended that you use the manufacturer's approved
Stainless Steel Cleaner and Polish. To order the cleaner,
refer "Accessories" section.
IMPORTANT:
This cleaner is for stainless steel parts only!
Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If unintentional contact
does occur, clean plastic part with a sponge and mild
detergent in warm water. Dry immediately with a soft, dry
cloth to absorb any remaining water.
5. Replace the racks.
Condenser cleaning
Explosion Hazard
Risk of fire or explosion due to puncture of refrigerant
tubing.
Follow handling instructions carefully.
Flammable refrigerant used.
1. Remove the base grille to access condenser for cleaning.
Refer "Removing Base Grille" section.
2. Clean the condenser coils regularly. They are located
behind the base grille. Coils may need to be cleaned as
often as every other month. This may help save energy.
Removing Base Grille
You must remove the base grille to access the condenser
coils for cleaning.
To remove the base grille:
1. Open the beverage center door.
A. Screws
A
02/02/21 16:07
02/02/21 16:07
Publicidad
