cecotec CONGA ROCKSTAR 2500 ULTIMATE ERGOWET Manual De Instrucciones página 28

ENGLISH
brush head rests on the floor to avoid the charging base from holding all the vacuum
cleaner's weight.
Drill the 3 holes (previously marked) and insert the pegs and M4 x 32 mm screws.
2.
Make sure that the charging base is securely fixed on the wall and place the vacuum
3.
cleaner on the charging base by placing the vacuum cleaner charging terminals over the
charging base charging terminals (plastic tab).
Once the wall charging base is installed, the charging port must be connected to the
4.
power adapter, and then the device can be charged by sliding it from top to bottom into
the wall charging base. Fig. 12
Charge and display
- When the battery percentage is 20 % or below, the device will automatically enter
low consumption mode. It is recommended to charge the device when it reaches this
percentage.
- The battery must be charged with the charging base while it is connected to the main body.
Connect one of the ends of the power adapter to the power supply and the other to the
charging base. Fig. 8
- During charging, the charge light indicator will turn on red and the display will show the
current charge percentage. When the device is fully charged, the battery indicator will turn
green and the display will show 100%. Fig. 13
- You can also charge the battery without using the charging base. You can charge the
battery when the battery is installed or not in the device. Connect the adapter and connect
the other end to the battery, paying attention to the direction. Once it is properly connected,
the charge light indicator will turn on red and will turn green once the charge is complete.
Fig. 14
5. WATERTANK ACCESSORY
- Do not use cleaning agents. Use clean and room temperature water only. Do not use the
vacuum cleaner to vacuum water.
- When the vacuum cleaner is not going to be used for a long time, please remove the
water tank and empty the remaining water. Do not expose it to direct sunlight or to damp
environments.
Mop installation
- Place the mop cloth on the ground with the Velcro facing upwards.
- Align the mop cloth with the Velcro strips on the tank and attach it. Align the mop cloth
with the Velcro strips on the water tank and attach it without covering the wheels. Fig. 15
54
Replacing the mop
- Remove the water tank from the device.
- Use your foot to hold the accessory against the ground and pull the vacuum cleaner
upwards until both parts are separated.
- Replace the mop and refill the water tank.
- Install the water tank again, insert the tank in the lower part of the vacuuming brush head
and press until it is fixed.
Water
Fig. 16
- When using this product for the first time, make sure the water tank lid is not fully open.
- When not in use, pay attention to the water emission push button and to the tank lid, as
water leak may occur when the water tank is full.
- To activate the water emission, the water emission push button must be pressed, and to
stop the water emission, the push button must be in the original position, as shown in
figure 16.
6. CLEANING AND MAINTENANCE
- Turn the appliance off, unplug it from the power supply and allow it to cool down before
cleaning it.
- Use a soft, slightly dampened cloth to clean the device's surface.
- Never immerse the device in water or other liquids, do not allow liquids to enter the device.
- Do not use abrasive cleaners or scouring pads to clean the product.
- Do not leave the device in a place with direct sunlight.
- Do not leave the device in a wet place after cleaning it.
- After the brush has been used for a long time, bristles might start to tangle with hair and
other particles. Clean it in order for it to operate correctly again.
Filters and tank cleaning
- To avoid the appliance from overheating and losing suction power, it is suggested to clean
the filters frequently. To make the most of the suction power, it is suggested to clean the
filter after every use.
- The filters shelf life will depend on the accumulated use and the type of particles which are
frequently vacuumed. It is recommended to replace the filters every 6 months.
- To remove the filters (Fig. 17):
Press the dust tank opening button, marked with the word "CLEAN", and pull on the
1.
metallic handle to remove the filtering system.
Once the filtering system is out, turn the metallic handle anticlockwise and you will be
2.
ENGLISH
emission
CONGA ROCKSTAR 2500 X-TREME ULTIMATE ERGOWET 55