Whirlpool WFE 2B19 X Manual De Instrucciones página 2

OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
HALF LOAD - If there are not many dishes to be washed, a half loading
may be used in order to save water, electricity and detergent.
Remember to halve the amount of detergent.
TABLET (Tab)- If you use powder or liquid detergent, this option
should be off.
LOADING THE RACKS
UPPER RACK
ADJUSTABLE
(loading example for the
upper rack)
Load delicate and light
dishes: glasses, cups,
saucers, low salad bowls.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
1 2
A
In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds
etc.) please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
TROUBLESHOOTING
PROBLEMS POSSIBLE CAUSES
The dishwasher
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
does not fill the
water.
The inlet hose is bent.
All LEDs are
The sieve in the water inlet hose is clogged; it is
blinking rapidly
necessary to clean it.
Drain hose positioned too low or siphoning into
Dishwasher finishes
home sewage system.
the cycle prematurely.
Air in water supply.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-
sales Service, please state the codes provided on your product's identification plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model
identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.
2
FOLDABLE
FLAPS WITH
POSITION
(loading example for the lower rack)
For pots, lids, plates, salad bowls, cutlery etc.. Large
plates and lids should ideally be placed at the sides
to avoid interferences with the spray arm.
3
B
A
C
Please scan the QR code on your product in order to have more detailed information.
DELAY - It is possible to delay the start time of the program by 2, 4 or 8
hours.
The DELAY function cannot be set once a wash cycle has been started.
LOWER RACK
More information in the Daily Reference Guide on website.
CLEANING THE SPRAY ARMS
4
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
Please scan the QR code on your product in order to have more detailed information.
SOLUTIONS
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher and
reboot.
After having carried out the verification and cleaning, turn off and turn on the dishwa-
sher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Check water supply for leaks or other issues letting air inside.
CAPACITY: 14 standard place-settings
CUTLERY BASKET
The basket is equipped with top grilles for improved
cutlery arrangement. The cutlery basket should be
positioned only at the front of the lower rack.
Knives and other utensils with sharp edges
must be placed in the cutlery basket with the
points facing downwards or they must be posi-
tioned horizontally in the tip-up compartments
on the upper rack.
The lower spray arm may
be removed by pulling it
upwards.
IEC 436
:
400011694614
09/2023 dk - Xerox Fabriano