Publicidad
Idiomas disponibles
Idiomas disponibles
•
Information about, and help with, product parts and
servicing.
To start to use Husqvarna Connect
1. Download the Husqvarna Connect app on your
mobile device.
2. Register in the Husqvarna Connect app.
3. Follow the instruction steps in the Husqvarna
Connect app to connect and register the product.
Note:
Husqvarna Connect app is not available for
download in all markets. Speak to your servicing
dealer for more information.
To unfold and fold the transport handle
•
To unfold the transport handle, push the buttons
on the left and right side and pull up the transport
handle. (Fig. 18)
•
To fold the transport handle, push the buttons on
the left and right side and push down the transport
handle. (Fig. 19)
To install the spray handle
1. Pull out the high-pressure water hose. (Fig. 20)
2. Hold the spray handle tightly with one hand and
push the high-pressure water hose into the quick
connection on the spray handle.
a) PW 350 (Fig. 21)
b) PW 360 and PW 370 (Fig. 22)
To remove the spray handle
1. Push the tab in the direction of the quick connection
on the spray handle and pull out the high-pressure
water hose.
a) PW 350 (Fig. 23)
b) PW 360 and PW 370 (Fig. 24)
2. Turn the hose reel clockwise until the high-pressure
water hose is fully wound. (Fig. 25)
To install the spray lance
1. Hold the spray handle with one hand and push the
coupling on the spray lance into the spray handle.
a) PW 350 (Fig. 26)
b) PW 360 and PW 370 (Fig. 27)
2. Turn the spray lance clockwise and release the
spray lance. The spray lance locks in position.
To remove the spray lance
1. Push in the spray lance and turn it counterclockwise.
a) PW 350 (Fig. 28)
b) PW 360 and PW 370 (Fig. 29)
2. Pull out the spray lance from the spray handle.
2167 - 004 - 18.12.2023
Nozzles (PW 350)
The product is supplied with 3 nozzles:
•
One nozzle with a rotating water jet, identified with
"ROUGH NOZZLE".
•
One nozzle with straight water jet, identified with
"GENTLE NOZZLE".
•
One nozzle with straight water jet, identified with
"SHORT NOZZLE".
The nozzle identified with "ROUGH NOZZLE" can be
used to clean surfaces that are not sensitive, for
example driveways. The nozzle identified with "GENTLE
NOZZLE" can be used to clean sensitive surfaces, for
example vehicles. The nozzle identified with "SHORT
NOZZLE" has a straight water jet with low pressure
that can be used to lightly flush a surface. It cannot be
installed on the spray lance.
(Fig. 30)
To install and remove a nozzle on the spray
lance (PW 350)
CAUTION:
a rotating water jet on sensitive surfaces, for
example painted surfaces on a vehicle. The
rotating water jet can cause damage to the
surface.
•
To install a nozzle, hold the spray lance with one
hand and push in the nozzle until it locks in position.
(Fig. 31)
•
To remove a nozzle, push in the tab on the spray
lance and pull out the nozzle from the spray lance.
(Fig. 32)
To adjust the pressure of the water jet (PW
350)
The nozzle with a straight water jet has adjustable
pressure.
•
To increase the pressure of the water jet, turn the
nozzle clockwise. (Fig. 33)
•
To decrease the pressure of the water jet, turn the
nozzle counterclockwise. (Fig. 34)
To install and remove the short nozzle for the
spray handle (PW 350)
•
To install the nozzle, hold the spray handle with one
hand and push the coupling on the nozzle into the
spray handle. Turn the nozzle clockwise and release
the nozzle. The nozzle locks in position. (Fig. 35)
•
To remove the nozzle, push in the nozzle and turn
it counterclockwise. Pull the nozzle from the spray
handle. (Fig. 36)
Do not use the nozzle with
21
Publicidad
