Bimar SE1800.EU Folleto De Instrucciones página 13

Fax +32 030 9904733
utensil from being pulled over. Check that you cannot trip over to prevent accidental falls or harm
to persons.
• Do not use the heater with a timer or a programmer or any other device that switches the heater on
automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
• All repairs should be made by a competent qualified electrician. In any case you should return the
appliance to this service.
ASSEMBLY
Attention: The appliance may only be used if complete with the support.
ATTENTION: The heater must not be used if the candle are damaged.
To assemble, follow these instructions:
- Attach the lower column (7) to the base (3) by inserting it into its seat, with the screw (1)
- Connect the intermediate column (8) to the lower one and then the upper one (9), attaching them
with the screws provided (6)
- Connect the body (16) to the upper column and attach it by tightening the screw (15).
- Hook the electric cord to the ring (5).
OPERATION
The heater havea "pull switch" to select the heater's power with a display that shows the selection: 0 =
off, I = 1800W. The selection changes each time you pull the cord.
There is also a safety switch that turns off the radiant part if the heater tips over.
The heating part can be oriented and positioned at the most convenient height: the height (max =
1,85m) is adjusted by raising or lowering the telescoping tube (then tighten the
locking ring) and the infrared radiation and heat is oriented by tilting the heating part (angle = 25°
max).
Before each use, make sure the device is in good condition and that the electric cord is not damaged
(if in doubt, contact professionally qualified personnel). Before plugging the cord into the socket,
make sure the switch is off and that the heating part is oriented conveniently. Then proceed as
follows:
1) Plug it in
2) Select the power
3) To turn the heater off, pull the cord of the "pull switch" until you see "0" on the display. To turn
oscillation off, push the button to the "OFF" position and plug out from the current socket.
Never leave the appliance connected to the socket if it is not in use, especially for long periods.
CLEANING AND MAINTENANCE
Attention: before cleaning the appliance, switch it off, remove the plug from the current socket and leave it
until getting cool.
•
Protect the radiant part from dust to preserve its reflectivity.
•
To clean the base, use a slightly damp, soft cloth; do not use scouring pads or abrasive products.
•
To clean the radiant part, use a slightly damp, soft cloth; do not use metal scouring pads or abrasive
products, water or other liquids; do not immerse in water or other liquids.
•
When not being used, cover it and put it in a dry place; it is a good idea to put it back in its original
packaging to protect it from dust and humidity.
•
A special tool is required to replace the electrical cord and resistance (220-240V~ 1600-1900W): contact
an authorized service center, also for any repairs.
•
Should you decide not to use the appliance any more, we recommend making it inoperative by cutting
the power cord (after making sure you have disconnected the plug from the socket) and make dangerous
parts harmless if children are allowed to play with them, such as the heating elements.
•
If you decide not to use the appliance any more, we recommend making it inoperative by cutting the
power cord (after making sure you have disconnected the plug from the socket) and make dangerous
parts harmless if children are allowed to play with them.
•
Do not dispose of non-biodegradable products in the environment but dispose of them in accordance with
current law. At the end of its working life, the product must not be disposed of as urban waste. It must be
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar
(Italy). The pages must be reproduced and folded in
order to obtain a booklet A5 (+/- 148.5 mm width x 210
mm height). When folding, make sure you keep the good
numbering when you turn the pages of the I/B. Don't
change the page numbering. Keep the language
integrity.
13/36
Assembly page 13/36