Publicidad
Idiomas disponibles
Idiomas disponibles
1,
2,
INSTALLATION
Run some water
from
the hot
and cold faucets
to flush
the
water
lines
and
remove
particles
that might
clog up the
water
valve
screens.
Remove
the
inlet
hoses
and
rubber
washers
from
the
plastic
bag
and
install
the
rubber
washers
in each
end
of the inlet hoses.
Carefully
connect
the inlet hose
(90 ° elbow end) marked
"HOT"
to the outside
"H" outlet of the
water valve. Tighten by hand, then
_}
tighten another
2/3 turn with pliers.
Carefully connect the other irrlet hose to the inside "C"
outlet of the water valve. Tighten by hand, then tighten
another 2/3 turn with pliers. Do not crossthread
or
over-tighten
these connections.
Corrnect the irrlet hose ends to the HOT and COLD water
faucets tightly by hand, then tighten
another 2/3 turn with
pliers. Turn the water on arrd check for leaks.
NOTE:
Use only new hoses.
Carefully
move the washer to its final location.
NOTE:
Do not use the dispenser
drawer
or door to lift
washer.
With the washer
in its final position,
place a level on top of
the washer, no rocking of the washer should exist. Adjust the
front leveling legs up or down to ensure the washer is resting
solid. Rear leg adjustment
is accessible through
the front
service panel. Turn the lock nuts on each leg up towards the
base of the washer and snug with a wrench.
NOTE:
Keep the leg extension
at a minimum
to prevent
excessive vibration.
The farther
out the legs are
extended the more the washer will vibrate.
Form a U shape on the end of the drain hose with the hose
pointed toward
the drain. Place in a laundry tub or standpipe
arrd secure with
the cable tie provided
in the enclosure
package.
NOTE:
If the drain hose is placed in a standpipe
without
forming
a U shape, a siphoning action could occur.
There must be an air gap around the drain hose. A
snug hose fit can also cause a siphoning
action.
Cable Tie
;)
Cable
Tie
13.
NOTE:
Cable
Tie
8.
Plug the power
cord
into a grounded
outlet.
NOTE:
Check to ensure the power
is off at a circuit
breaker/fuse
box before
plugging
the power
cord
into an outlet.
9.
Turn on the power at a circuit breakefifuse
box.
10.
Read the Operating Instructions and Owner_ Guide provided
with
the washer.
They
contain
valuable
and helpful
information
that will save you time and money.
11.
Run the washer through
a complete
cycle. Check for water
leaks and proper operation.
12. If your
washer
does
not
operate,
please
review
the
"Avoid
Service Checklist"
in your Owner's
Guide before
calling
for
service.
Place these
instructions
in a location
near the washer
for future
reference.
A wiring
diagram
is located
irrside the washer
on
the service
panel.
REPLACEMENT
PARTS
If replacement parts are needed for your washer, call
Sears Parts and Service Toll Free Number 1-800-4-MY-
HOME
TM
(1-800-469-4663).
Destroy the carton and plastic bags
after the washer is unpacked. Children might use them
for play. Cartons covered with rugs, bedspreads, or
plastic sheets can become airtight chambers causing
suffocation. Place all materials in a garbage container
or make materials inaccessible to children.
The instructions in this manual and all
other literature included with this washer are not meant
to cover every possible condition
and situation that
may occur. Good safe practice and caution MUST be
applied when installing, operating and maintaining any
appliance.
Maximum
benefits and er]joyment are achieved
when all the Safety and Operating instructions are
understood and practiced as a routine with your
laundering tasks.
Publicidad
