Publicidad
Idiomas disponibles
Idiomas disponibles
TO START ENGINE
NOTE: Due to protective
coatings on the
engine, a small amount
of smoke may be
present during the initial use of the
product and should be considered
normal.
1. To start a cold engine, push primer
three (3) times before trying to start.
Use a firm push. This step is not
usually necessary when starting an
engine which has already run for a
few minutes.
2.
Move throttle control lever to FAST
position.
3.
Hold operator presence
control bar
down to the handle and pull starter
handle quickly. Do not allow starter
rope to snap back.
TO STOP
ENGINE
• To stop engine, release operator
presence
control bar.
NOTE:
In cooler weather it may be
necessary to repeat priming steps. In
warmer weather over priming may cause
flooding and engine will not start. If you
do flood engine, wait a few minutes
before attempting to start and do not
repeat priming
steps.
MOWING TIPS
• Under certain conditions, such as very
tall grass, it may be necessary to raise
the height of cut to reduce pushing
effort and to keep from overloading the
engine
and leaving
clumps of grass
clippings.
It may also be necessary to
reduce ground
speed
and/or run the
lawn mower over the area a second
time.
• For extremely
heavy cutting, reduce the
width of cut by overlapping previously
cut path and mow slowly.
• For better grass bagging and most
cutting conditions, the engine speed
should be set in the fast position.
• When using a rear discharge
lawn
mower in moist, heavy grass, clumps of
cut grass may not enter the grass
catcher.
Reduce
ground
speed
(pushing speed) and/or
run the lawn
mower over the area a second time.
• It a trail of clippings is left on the right
side of a rear discharge mower, mow in
a clockwise direction with a small
overlap to collect the clippings on the
next pass.
• Pores in cloth grass catchers can
become filled with dirt and dust with
use and catchers
will collect less grass.
To prevent this, regularly
hose catcher
off with water and let dry before using.
• Keep top of engine around starter
clear
and clean of grass clippings
and chaff.
This will help engine
air flow and
extend
engine
life.
MULCHING
MOWING
TIPS
IMPORTANT:
For best performance,
keep mower housing free of built-up
grass and trash. See "CLEANING"
in the
Maintenance
section of this manual.
• The special mulching blade will recut the
grass clippings many times and reduce
them in size so that as they fall onto the
lawn they will disperse into the grass and
not be noticed. Also, the mulched grass will
biodegrade quickly to provide nutrients for
the lawn. Always mulch with your highest
engine (blade) speed as this will provide
the best reouffing action of the blades.
• Avoid cutting your lawn when it is wet. Wet
grass tends to form clumps and interferes
with the mulching action. The best time to
mow your lawn is the early afternoon. At
this time the grass has dried and the newly
cut area will not be exposed to the direct
sun.
• For best results, adjust the lawn mower
cutting height so that the lawn mower cuts
off only the top one-third of the grass
blades. If the lawn is overgrown it will be
necessary to raise the height of cut to
reduce pushing effort and to keep from
overloading the engine and leaving
clumps of mulched grass. For extremely
heavy grass, reduce your width of cut by
overiapping previously cut path and mow
slowly.
MAXI_
• Certain types of grass and grass condi-
tions may require that an area be mulched
a second time to completely hide the
clippings. When doing a second cut, mow
across or perpendicular to the first cut path.
• Change your cutting pattern from week to
week. Mow north to south one week then
change to east to west the next week. This
will help prevent matting and graining of
the lawn.
9
Publicidad
