Silverline 140878 Traducción Del Manual Original página 7

Product Familiarisation
1. Forehead Protector
2. Headband
3. Strap Adjuster
4. Headband Slot
5. Mesh Visor Hinge
6. Headband Ear Cup Slot
7. Ear Cup Connector
8. Ear Cup
9. Forehead Strap
10. Mesh Visor
11. Mesh Visor Pins
Intended Use
Provides protection when using electric, battery and petrol garden power tools, including chainsaws,
strimmers, hedge cutters and lawn mowers that create high noise levels and may throw dust and
debris towards the face of the operator.
Assembly and Fitting
1. Position the Ear Cup (8) halfway on the Headband Ear Cup Slot (6) (Image A) and turn the Ear
Cup so the Ear Cup Connector (7) is in line with the Headband Ear Cup Slot (Image B) to remove
the Ear Cup from the Headband (2)
2. Locate the two Headband Slots (4) (Image C) and carefully insert one end of the Headband into
each slot (Image D)
3. Feed the ends through the Headband Slots until you reach the angled part of the Headband
(Image E)
4. Refit the Ear Cups to the Headband by positioning them halfway on the Headband Ear Cup Slot
and turning to secure
5. Fit the Mesh Visor (10) over the Mesh Visor Pins (11) (Image F) then turn the pins 180° to secure
(Image G & H). Check it is secure and correctly positioned (Image I)
6. The forestry hat is now assembled (Images L & M) but adjustments must be made to ensure
a good fit
• The height of the Ear Cups can be adjusted in the Headband Slots for maximum sound
attenuation and comfort.
• Adjustments to the top of the Headband are to be made prior to wearing the forestry hat (Image
J). When correctly adjusted there should be no gap between the Headband and the top of
the head.
• The Strap Adjuster (3) that sits on the rear of the forestry hat can be adjusted while fitted to the
head (Image K). Turning the Strap Adjuster clockwise will reduce the length of the strap and
anti-clockwise will increase it. Do not force the Strap Adjuster when it has reached its minimum
or maximum strap length.
WARNING: These ear muffs are of 'medium size range' . Ear muffs complying with EN352-1
are of 'medium size range' or 'small size range' or 'large size range' . 'Medium size range' ear muffs
will fit the majority of wearers. 'Small size range' or 'large size range' ear-muffs are designed to fit
wearers for whom 'medium size range' ear muffs are not suitable.
Markings
Symbol on mesh eye and face protection
Silverline
EN
F
UKCA
CE
Explanation
Manufacturer
Number of standard which product fulfils
Protection against high speed particles in low
energy impacts
United Kingdom Conformity Assessed
CE certification
WARNING: Mesh oculars and visors marked 'S' should not be used when there is a foreseeable
risk of any hard or sharp flying particles.
Storage and Maintenance
When not in use, the forestry hat must be stored in a clean and dry environment. This product
should be inspected regularly for serviceability. Any part which comes into contact with the wearer
should be disinfected with agents known not to be harmful to the user. Clean with warm soapy
water and dry with soft cloth. Do not clean with abrasive materials, organic solvents or alcohol. Ear
defenders should be disinfected every 3 months.
Contact
Legal Manufacturer: Toolstream Ltd
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: www.silverlinetools.com
UK Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B.V.
Holtum-Noordweg 11
Unit 4
6121 RE Born
The Netherlands
Notified body: PZT GmbH
An der Junkerei 48, Wilhelmshaven 26389
Notified body number: 2754
Approved body: SATRA Technology Centre
Wyndham Way, Telford Way, Kettering, Northamptonshire, NN16 8SD, United Kingdom
Approved body number: 0321
silverlinetools.com
Mesh Forestry Hat
7