Publicidad
Idiomas disponibles
Idiomas disponibles
13.0
In "Synergic ON" and "pulsed" Mode use the Material Key - 6.2.2 - to enter the synergic programs list.
Synergic ON
N
Material
01
Fe
02
Fe
03
Fe
04
Fe
05
Fe
06
Fe
07
CrNi
08
CrNi
09
Al
10
Al
11
CuSi
12
CuSi
13
MSIP1
Pulsed
20
AlMg
21
AlMg
22
AlMg
23
AlMg
24
AlSi
25
AlSi
26
AlSi
27
Fe
28
Fe
29
CrNi
30
CrNi
31
CrNi
32
CrNi
14.0
METAL
Mild steel
Mild steel - Pulsed Mode
Aluminium
Stainless steel
Copper, Nickel and
Alloys
Contact the technical service of your gas supplier to know the percentages of the different
gases which are the most suitable to your application.
15.0
•
Always weld clean, dry and well prepared material.
•
Hold gun at a 45° angle to the workpiece with nozzle about 5 mm from the surface.
•
Move the gun smoothly and steadily as you weld.
•
Avoid welding in very drafty areas. A weak pitted and porous weld will result due to air blowing away
the protective welding gas.
•
Keep wire and wire liner clean. Do not use rusty wire.
•
Sharp bends or kinks on the welding cable should be avoided.
•
Always try to avoid getting particles of metal inside the machine since they could cause short circuits.
•
Use compressed air to periodically clean the hose liner when changing wire spools
IMPORTANT: Disconnect from power source when carrying out this operation.
•
Using low pressure air (3/5 Bar=20-30 PSI), occasionally blow the dust from the inside of the welder. This keeps
the machine running cooler. Note: do not blow air over the printed circuit board and electronic components.
•
The wire feed roller will eventually wear during normal use. With the correct tension the pressure
roller must feed the wire without slipping. If the pressure roller and the wire feed roller make contact
(when the wire is in place between them), the wire feed roller must be replaced.
•
Check all cables periodically. They must be in good condition and not cracked.
20
20
SYNERGIC PROGRAMS LIST
Gas
CO2
CO2
CO2
ArCO2
ArCO2
ArCO2
ArCO2
ArCO2
Ar
Ar
Ar
Ar
ArCO2
Ar
Ar
Ar
Ar
Ar
Ar
Ar
ArCO2
ArCO2
ArCO2
ArCO2
C2-98%Ar-2% CO2
C2-98%Ar-2% CO2
PROTECTION GASES GUIDE
GAS
CO2
Argon + CO2
Argon + CO2 + Oxygen
98%Argon + 2% CO2 (C2)
Argon
Argon + Helium
98%Argon + 2% CO2 (C2)
80% Argon + 20% CO2
Argon + CO2 + Oxygen
Argon + Oxygen
Argon
Argon + Helium
WELDING HINTS AND MAINTENANCE
Diameter
0.6
0.8
1.0
0.6
0.8
1.0
0.8
1.0
0.8
1.0
0.8
1.0
0.6
0.8
Normal
1.0
Normal
1.2
Normal
1.0
Low Energy
0.8
Normal
1.0
Normal
1.2
Normal
0.8
Normal
1.0
Normal
0.8
Normal
1.0
Normal
0.8
Normal
1.0
Normal
NOTE
High Penetration
Argon controls spatters
Oxygen improves arc stability
Recommended.
Arc stability, good fusion and minimum spatter.
Higher heat input suitable for heavy sections.
Minimum porosity.
Recommended.
Arc stability.
Minimum spatter.
Suitable for light gauges because of low flowability
of the weld pool.
Higher heat input suitable for heavy sections.
(to close gap or very thin gauges)
39
Publicidad
