Publicidad
Idiomas disponibles
Idiomas disponibles
7.0 DESCRIPTION OF SW1 DIP-SWITCHES
1 "AND-OR" SELECTION
OFF: AND operation
ON: OR operation
2 ALARM STORAGE FUNCTION
OFF: STORAGE ENABLED
ON: STORAGE DISABLED
3 MICROWAVE DELAY
OFF: Minimum delay
ON: Maximum delay
4 "DUAL EDGE" SIGNAL DETECTION
OFF: SINGLE EDGE signal detection
ON: DUAL EDGE signal detection
5 PULSE COUNT
OFF: X 1 COUNT
ON: X 2 COUNT
6 "TE" SIGNAL SELECTION
OFF: low active TE
ON: high active TE
7 RELAY BLOCK FUNCTION
OFF: the TC blocks relays
ON: the TC does not block relay
8 "TC" SIGNAL INDICATION
OFF: low active TC
ON: high active TC
NOTE: when using CURTAIN coverage or LONG RANGE, coverage dip
switch n.4 and n.5 must be OFF
7.0 DESCRIPTION OF SW1 DIP-SWITCHES
1 "AND-OR" SELECTION
OFF: AND operation
ON: OR operation
2 ALARM STORAGE FUNCTION
OFF: STORAGE ENABLED
ON: STORAGE DISABLED
3 MICROWAVE DELAY
OFF: Minimum delay
ON: Maximum delay
4 "DUAL EDGE" SIGNAL DETECTION
OFF: SINGLE EDGE signal detection
ON: DUAL EDGE signal detection
5 PULSE COUNT
OFF: X 1 COUNT
ON: X 2 COUNT
6 "TE" SIGNAL SELECTION
OFF: low active TE
ON: high active TE
7 RELAY BLOCK FUNCTION
OFF: the TC blocks relays
ON: the TC does not block relay
8 "TC" SIGNAL INDICATION
OFF: low active TC
ON: high active TC
NOTE: when using CURTAIN coverage or LONG RANGE, coverage dip
switch n.4 and n.5 must be OFF
8.0 DESCRIPTION OF SW2 DIP-SWITCHES
1
MW SYNCHRONISM MASTER/SLAVE SENSOR
OFF: SLAVE sensor
ON: MASTER sensor
2
MW SYNCHRONISM SLAVE 1/SLAVE 2 SENSOR
OFF: SLAVE 1 sensor
ON: SLAVE 2 sensor
3
TYPE OF TEST WITH "TE" SELECTION
OFF: TE entry enabled for walk test
ON: TE entry enabled for remote test
4
ADJUSTMENT OF INFRARED SENSITIVITY
OFF: high sensitivity (15 m)
ON: low sensitivity (9 m)
5
ZONE (MW/PIR) LED ENABLING
OFF: Leds enabled for operation
ON: Leds not enabled
6
GENERAL (ALARM) LED ENABLING
OFF: Led enabled for operation
ON: Led not enabled
7
FAULT INDICATION
OFF: the fault indication does not allow alarm contact opening
ON: the fault indication allows alarm contact opening
8
ANTIMASKING INDICATION (IM915AM only)
OFF: the antimasking indication does not allow alarm contact opening
ON: the antimasking indication allows alarm contact opening
15
8.0 DESCRIPTION OF SW2 DIP-SWITCHES
1
MW SYNCHRONISM MASTER/SLAVE SENSOR
OFF: SLAVE sensor
ON: MASTER sensor
2
MW SYNCHRONISM SLAVE 1/SLAVE 2 SENSOR
OFF: SLAVE 1 sensor
ON: SLAVE 2 sensor
3
TYPE OF TEST WITH "TE" SELECTION
OFF: TE entry enabled for walk test
ON: TE entry enabled for remote test
4
ADJUSTMENT OF INFRARED SENSITIVITY
OFF: high sensitivity (15 m)
ON: low sensitivity (9 m)
5
ZONE (MW/PIR) LED ENABLING
OFF: Leds enabled for operation
ON: Leds not enabled
6
GENERAL (ALARM) LED ENABLING
OFF: Led enabled for operation
ON: Led not enabled
7
FAULT INDICATION
OFF: the fault indication does not allow alarm contact opening
ON: the fault indication allows alarm contact opening
8
ANTIMASKING INDICATION (IM915AM only)
OFF: the antimasking indication does not allow alarm contact opening
ON: the antimasking indication allows alarm contact opening
15
Publicidad
