Elite RACE FC Instrucciones página 8

EN
Thank you for choosing the
Workstand Race FC
IMPORTANT
1. Be sure to set Workstand Race on a flat stable surface to
prevent it from collapsing.
2. Make sure the legs are completely opened and blocked
to ensure proper stability.
3. Before starting to work on the bicycle, position the
Workstand in a suitable place, away from potentially
dangerous objects (furniture, tables, chairs, etc.) in order
to prevent any risk of unintentional or accidental contact
with them.
4. Keep people, children and animals away from the
Workstand during use, since parts of the Workstand or the
bicycle could cause damage in case of contact.
5. While closing the Workstand and during transportation
make sure that the handwheel of the bottom bracket
support (B) and the handwheel of the fork support (C) are
tightened so they are locked on the support arm, to avoid
losing them during transportation of the Workstand.
LIST OF PARTS
Nr. 1 Race FC Workstand (Ref. A)
Nr. 1 Bottom bracket support (Ref. B);
Nr. 1 Bicycle fork support (Ref. C);
Nr. 2 Quick Release Ø5mm Bushing Adapter (Ref. D);
Nr. 2 Thru-axle Ø12mm Bushing Adapter (Ref. E);
Nr. 1 Strap (Ref. F).
THESE FEATURES INCLUDE:
1. Extremely light, made from aluminium.
2. All the components are rustproof and very strong.
3. Folds quickly and compactly for easy transport to events.
4. Will accept virtually any bike (except tandems).
5. Maximum load: 18 Kg.
6. Bike can be attached by front fork or rear drops, as
needed. An additional bicycle fork support (C) to secure the
bicycle on both forks is available for purchase.
7. Fully height adjustable, with the ability to rotate the upper
portion as needed, even with bike attached.
8. Bike support arm quickly unfolds, snaps securely into
position.
9. Bike support arm collapses easily, by simply pressing
a trigger.
10. Rubber covered bottom bracket support protects your
bike's finish.
11. Attachment strap can be used from either side,
depending on how bike is mounted to the stand.
12. You can purchase the front Ø15 mm thru axle
8
separately.
USE
1. Remove the unit from the box and remove any internal
packing material (Pic. 1).
2. Open the legs (Pic. 2A- 2B).
3. Rotate the bike support arm upward until the release
trigger clicks into place (Pic. 3).
4. Subsequently, insert the safety plug in the designed slot .
(Pic. 4)
5. Loosen the QR lever on the plastic ring. (Pic.
6. Unscrew the height adjustment knob and move the
vertical tube of the stand to obtain the required height.
(Pic.6A) Close the knob to secure the position.
7. Slide the plastic ring (L) along the vertical tube (I) to the
joint of the legs (N) and close the quick release (H). The
height adjustment knob (M) can then be released and the
stand will remain at the same height, but the upper part
can rotate. To eliminate the rotation, tighten the adjustment
knob (M). (Pic. 6B)
8. To install the supports on the stand untighten the
handwheel as much as needed, once it's positioned tighten
it back. (Pic. 7A - 7B).
9. Insert the Strap (Ref. F) through the slot in the central
support, leaving the buckle on the side of the bicycle
opposite the chain (this depends on whether you're using
the front or rear fork) (Pic. 8).
BICYCLE WITH Ø 12/15 MM THRU-AXLE
1. Tighten the Ø12mm thru-axle bushing adapters (Ref.
E) (Ø 15mm thru-axle bushing not included, available for
purchase on shopelite-it.com) and adjust them based on
the width of your bicycle's fork (Pic. 9)
2. Remove whichever wheel as needed and rest the bike on
the bottom bracket support.
3. While holding the bicycle, place the fork (front Pic.10A -
rear Pic.10B) at the same height of the bushing, then insert
the thru-axle and secure it as on the wheel of the bicycle.
BICYCLE WITH Ø 5 MM QUICK RELEASE
1. Other than the bushing for thru-axle (E), bicycles with
quick release also need the provided quick release bushing
(D). (Pic. 11)
2. Remove whichever wheel as needed and rest the bike on
the bottom bracket support.
3. Place the fork of the bicycle so it is supported on the
bushing. (front Pic.12A - rear Pic. 12B)
4. Insert and adjust the quick clamping system so that it
firmly secures the forks and close it to lock the bicycle.
5. Loop the nylon strap (F) over the bike frame and through
the buckle and tighten it. (Pic.13A - 13B)
5)