Publicidad
Idiomas disponibles
Idiomas disponibles
GENERAL
SAFETY
INSTRUCTIONS
Operating
a Jointer/Planer
can be dangerous
if
safety and common
sense are ignored.
The
operator
must be familiar with the operation
of the
tool. Read this manual to understand
this Jointeri
Planer.
DO NOT operate
this Jointer/Planer
if you
do not fully understand
the limitations
of this tool.
DO NOT modify this Jointer/Planer
in any way.
BEFORE
USING THE JOINTER/PLANER
_!Vivlzl
t,_l _II _[e'll
To avoid serious injury and damage to the tool, read and
follow all of the Safety and Operating Instructions before
operating the Jointer/Planer.
1.
READ the entire Owner's Manual. LEARN how to
use the tool for its intended applications.
.
GROUND ALL TOOLS. If the tool is supplied with a
3-prong plug, it must be plugged into a 3-contact
electrical receptacle. The 3rd prong is used to
ground the tool and provide protection against
accidental electric shock. DO NOT remove the 3rd
prong. See Grounding Instructions on page 4.
3.
AVOID A DANGEROUS WORKING
ENVIRONMENT.
DO NOT Use electrical tools in a
damp environment or expose them to rain.
4.
DO NOT use electrical tools in the presence of
flammable liquids or gasses.
.
ALWAYS keep the work area clean, well lit, and
organized. DO NOT work in an environment with
floor surfaces that are slippery from debris, grease
or wax.
.
.
.
KEEP VISITORS AND CHILDREN AWAY. DO NOT
permit people to be in the immediate work area,
especially when the electrical tool is operating.
DO NOT FORCE THE TOOL to perform an
operation for which it was not designed. It will do a
safer and higher quality job by only performing
operations for which the tool was intended.
WEAR PROPER CLOTHING. DO NOT wear loose
clothing, gloves, neckties, or jewelry. These items
can get caught in the machine during operations and
pull the operator into the moving parts. The user
must wear a protective cover on their hair, if the hair
is long, to prevent it from contacting any moving
parts.
.
ALWAYS WEAR EYE PROTECTION.
Any power
tool can throw debris into the eyes during
operations, which could cause severe and
permanent eye damage. ALWAYS Wear Safety
Goggles (that comply with ANSI standard Z87.1)
when operating power tools. Safety Goggles are
available at Sears Retail Stores.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
WEAR A DUST MASK TO PREVENT INHALING
DANGEROUS
DUST OR PARTICLES.
ALWAYS UNPLUG THE TOOL FROM THE ELEC-
TRICAL RECEPTACLE when making adjustments,
changing parts or performing any maintenance.
KEEP PROTECTIVE
GUARDS IN PLACE AND IN
WORKING ORDER.
AVOID ACCIDENTAL
STARTING. Make sure that
the power switch is in the "OFF" position before
plugging in the power cord to the electrical
receptacle.
REMOVE
ALL MAINTENANCE
TOOLS from the
immediate area prior to turning "ON" the Jointer/Planer.
USE ONLY RECOMMENDED
ACCESSORIES.
Use
of incorrect or improper accessories could cause
serious injury to the operator and cause damage to
the tool. If in doubt, check the instruction manual
that comes with that particular accessory.
NEVER LEAVE A RUNNING TOOL
UNATTENDED.
Turn the power switch to the "OFF"
position. DO NOT leave the tool until it has come to
a complete stop.
DO NOT STAND ON A TOOL. Serious injury could
result if the tool tips over or you accidentally contact
the tool.
DO NOT store anything above or near the tool
where someone might try to stand on the tool to
reach it.
MAINTAIN YOUR BALANCE. DO NOT extend yourself
over the tool. Wear oil resistant, rubber-soled shoes.
Keep floor clear of debris, grease, and wax.
MAINTAIN TOOLS WITH CARE. Always keep tools
clean and in good working order. Keep all blades
and tool bits sharp.
SAVE THESE INSTRUCTIONS.
3
Publicidad
