HP COLOR LASERJET PRO MFP M177 Guia De Instalacion
Ocultar thumbs
Ver también para COLOR LASERJET PRO MFP M177:
- Guia del usuario (122 páginas) ,
- Guia de inicio rapido (49 páginas) ,
- Guía de inicio (25 páginas)
Manuales relacionados para HP COLOR LASERJET PRO MFP M177
Resumen de contenidos para HP COLOR LASERJET PRO MFP M177
- Página 1 COLOR LASERJET PRO MFP M177 *CZ165-90939* *CZ165-90939* CZ165-90939 Installation Guide Guide d'installation Guía de instalación Guia de instalação 安裝指南 מדריך התקנה Lea esto primero...
- Página 2 15° - 30°C (59° - 86°F) 10% - 80% Select a sturdy, well-ventilated, dust-free area, away from direct sunlight to position the product. Choisissez un support solide et un endroit propre, bien aéré et à l'abri du rayonnement direct du soleil pour placer votre produit. Busque una superficie sólida en un lugar bien ventilado, sin polvo y alejado de la luz solar directa para colocar el producto.
- Página 5 1. Connect the phone cord for fax. A country/region specific adapter for the RJ11 telephone cord may be required to connect to the telephone jack. 2. Optional: To connect an extension phone, connect another phone cord to the bottom phone port. 1.
- Página 6 1. Connect the power cord between the product and a grounded AC outlet. Make sure your power source is adequate for the product voltage rating. The voltage rating is on the product label. The product uses either 100-127 Vac or 220-240 Vac and 50/60 Hz. CAUTION: To prevent damage to the product, use only the power cord that is provided with the product.
- Página 7 1. 使 用電源線連接產品及接地的 AC 插座。確定電源符合產品的額定電壓。額定電壓標示在產品標籤上。本產品使用的電壓為 100-127 伏特或 220-240 伏特的交流電，50/60 赫茲。 注意：為了避免產品損壞，請僅使用產品隨附的電源線。 2. 開啟本產品電源。 3. 若要確認產品能列印，請依序點選設定 按鈕、報告以及組態報告。 4. 若要測試平台式掃描器，請將列印的報告正面朝下置於掃描器玻璃板上。在控制面板上，點選影印，然後點選彩色或黑白開始影 印。 5. 若要測試文件進紙器，請將列印的報告正面朝上裝入文件進紙器。在控制面板上，點選影印，然後點選彩色或黑白開始影印。 . מוארק. ודא שמקור המתח שלך מתאים לדירוג המתח של המוצר. דירוג המתח מופיע על תווית המוצרAC 1. חבר את כבל החשמל בין המוצר ושקע .
- Página 8 Choose a software install method. NOTE: You must have administrator privileges on the computer to install the software. Choisissez une méthode d'installation logicielle. REMARQUE : Vous devez disposer des privilèges d'administrateur sur cet ordinateur pour installer le logiciel. Seleccione un método de instalación de software. NOTA: Debe tener privilegios de administrador en el equipo para instalar el software.
- Página 9 Software installation for Windows wired networks: Connect the network cable to the product and the network. Insert the CD into the computer, and follow the on-screen instructions. Installation is complete. NOTE: If the installation program does not detect the product on the network, you might need to enter the IP address manually. The IP address is listed on the second page of the configuration report.
- Página 10 Software installation for Windows wireless networks: 1. On the product control panel, press the wireless button. Select Wireless Menu, and then select Wireless Setup Wizard. Follow the instructions to complete the wireless setup. 2. Insert the CD into the computer, and follow the on-screen instructions. Installation is complete. NOTE: If the installation program does not detect the product on the network, you might need to enter the IP address manually.
- Página 11 HP Smart Install drive to run the installation program. NOTE: If the HP Smart Install program fails, disconnect the USB cable, turn the product off and then on again, and then insert the product CD into your computer.
- Página 12 . ולחץ עליו פעמיים כדי להפעיל את תוכנית ההתקנהHP Smart Install את כונן , כבה את המוצר והפעל אותו שוב ולאחר מכן הכנס את תקליטור המוצרUSB- נכשלת, נתק את כבל הHP Smart Install הערה: אם פעולת התוכנית .למחשב. פעל לפי ההוראות שבמסך. חבר את הכבל רק כאשר התוכנה תנחה אותך לעשות זאת...
- Página 13 Software installation for Mac OS X: 1. If you are using a USB or a wired network connection, connect the cable now. 2. Insert the CD into the computer, and follow the on-screen instructions. Installation is complete. NOTE: For network connections, if the installation program does not detect the product on the network, you might need to enter the IP address manually.
- Página 14 Software installation for Mac wireless networks: 1. On the product control panel, press the wireless button. Select Wireless Menu, and then select Wireless Setup Wizard. Follow the instructions to complete the wireless setup. 2. Insert the CD into the computer, and follow the on-screen instructions. Installation is complete. NOTE: If the installation program does not detect the product on the network, you might need to enter the IP address manually.
- Página 15 O Guia do usuário e outras documentações estão no CD que acompanha o produto ou na pasta do programa HP no seu computador. Para usar o recurso HP ePrint, primeiramente é necessário ativar o HP Web Services. Toque no botão Web Services e em Ativar Web Services.
- Página 16 The information contained herein is subject to change without notice. sans préavis. The only warranties for HP products and services are set forth in the Les seules garanties pour les produits et services HP sont décrites dans express warranty statements accompanying such products and services.