FIRST AUSTRIA FA-2421-4 Manual De Instrucciones página 2

1
N
i
2
m_2421-4_v01.indd 54-3
iNSTRUCTioN MANUAl
FM CloCk RAdio WiTH TEMPERATURE
loCATioN oF CoNTRolS
(see fig. 1)
1. MEMORY/MEMORY+/NAP/AUTO 17. FM ANTENNA
oFF displaY 18. AC POWER CORD
2. alarM 1 on/oFF sEt 19. to sEt thE light intEnsitY
3. alarM 2 on/oFF sEt high
4. snooZE/slEEp/diMMEr 20. to sEt thE light intEnsitY
5. SET/TEMPERATURE LOW
6. <</TUNE-/YEAR/MONTH/DAY 21. light on/oFF
7. >>/TUNE+/DST/C-F 22. PROJECTION TIME 180° FLIP/TIME-
8. VoluME up/displaY auto tEMpEraturE
changE on/oFF 23. proJEction on/oFF
9. on/oFF 24. Focus adJustMEnt For
10. VOLUME DOWN proJEction unit
11. displaY lEd diSPlAY
12. BattErY coMpartMEnt (rEar a. pM indicator
OF UNIT) B. standBY indicator
13. laMp shadE c. alarM 1 indicator
14. RATING LABEL (REAR OF UNIT) d. Mhz indicator
15. SPEAKER E. alarM 2 indicator
16. tEMpEraturE sEnsor (in F. tiME indicator
DOOR)
PoWER CoNNECTioN
Plug the AC power cord to a household outlet AC source. This unit is equipped
with a battery back up system, it requires a 1x3V CR2032 Flat Lithium battery (Not
included). Insert the battery in the battery compartment, making certain that the
positive and negative (+ and -) battery terminals are attached to the corresponding
terminals on the plate in the battery compartment. If an AC power failure occurs, the
clock automatically switches to the battery power supply, the clock and timer memory
continue running. When the AC power resumes, the clock switches back to AC again.
gETTiNg STARTEd
TiME ANd CAlENdAR MANUAl SETTiNg
A. Setting Time and Calendar – Press Time set button (5) in normal mode and keep
depress over 2 seconds to enter time set mode, after enter the setting mode, press
Time set button (5) to change the mode cycle as follows:
Normal  Year  Month  Day  12/24h  Real time Hour  Real time Min 
Normal
Action (during data adjustment):
• Press <</Tune- button (6) to adjust data backward.
• Press >>/Tune+ button (7) to adjust data forward.
• Keep depress << or >> button for 2 seconds to enable auto forward.
B. Setting Alarm 1 and Alarm 2 – Press alarm set button (2/3) during normal mode
and keep depress over 2 seconds to enter alarm set mode, after enter the setting
mode, press alarm set button (2/3) to change the mode cycle as follows:
Normal  AL 1 Hour  AL 1 Min  AL 1 weekday Alarm  AL 1 wake beep  al 1
wake radio  AL 1 wake radio volume  Light  Light intensity  Normal
Normal  AL 2 Hour  AL 2 Min  AL 2 weekday Alarm  AL 2 wake beep  al 2
wake radio  AL 2 wake radio volume  Light  Light intensity  Normal
2
Select alarm weekday mode as follows
1-5: Monday to Friday
1-7: Whole week
6-7: Saturday & Sunday
1-1: One day of week
Action (during data adjustment):
• Press <</Tune- button (6) to adjust data backward.
• Press >>/Tune+ button (7) to adjust data forward.
• Keep depress << or >> button for 2 seconds to enable auto forward.
Alarm wake-up light:
The light will come on 5 minutes before the set alarm time. The light will start out at a
low level and increase gradually to the set max level.
AlARM dURATioN ANd SNooZE FUNCTioN
Alarm Duration – Beep alarm or radio alarm will continue output for 30 minutes if no
key press, then it will stop automatically and wait for same alarm time on next day.
Action for Snooze:
• During alarming, press Snooze button (4) will enable snooze function, Beep alarm
or Radio alarm will stop.
• Snooze interval is 9 minute (not include second offset)
• Snooze will continue unless press ON/OFF button to alarm off of Buzzer alarm or
Radio Alarm stop automatically after 30 minutes.
Display light ON/OFF function:
• Press Memory Set/memory+/Display light auto ON-OFF/NAP button (1) for 3
seconds, the LED display Indicator will light on, the LED display will turn off after
15 seconds automatically. Press any button to maintain the LED display for 15
seconds.
• Press Memory Set/Memory+/Display light auto ON-OFF/NAP button (1) for 3
seconds, the LED display indicator will light off to cancel this function.
AUTo CHANgE diSPlAY CoNTENT:
In radio off mode, press VOLUME UP/DISPLAY AUTO CHANGE ON/OFF button (8)
and keep depress over 2 seconds to enter time display auto change mode. To display
the Year and press again to display month/Day/Temperature, the display returns to
time display after 5 seconds. (see fig. 2)
liSTENiNg To RAdio
Press the ON/OFF button (9) to turn the unit on.
Use the Tune+ or Tune- button to select the desired FM station. If you press and hold
the Tune+ or Tune- button for one second, the release, the unit will automatically scan
to the next broadcasting station.
Press the ON/OFF button (9) to turn the radio OFF.
To SET/RECAll THE RAdio PRESETS
Press the ON/OFF button (9) to turn the unit ON.
Use the Tune+ or Tune- button to select the desired FM station.
Press the memory/memory+ button; "P01" will blink in the display.
Press the memory/memory+ button again to set the preset.
Repeat steps 2 through 4 to set more presets.
The unit can preset 10 stations totally for FM.
When "P01-P10" is blinking, press the Tune+ or Tune- button to select the preset
number.
Note:
Ensure that the FM antenna is completely unrolled and extended for best FM
reception.
3
12-8-8 下午2:29