Hikmicro HABROK Serie Guia De Inicio Rapido página 119

This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for
an uncontrolled environment.
Safety Instruction
These instructions are intended to ensure that user can use the product correctly
to avoid danger or property loss. Please read all the safety information carefully
before using.
Laws and Regulations
Use of the product must be in strict compliance with the local electrical safety
regulations.
Transportation
Keep the device in original or similar packaging while transporting it.

Keep all wrappers after unpacking them for future use. In case of any failure

occurred, you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage on the device

and the company shall not take any responsibilities.
Do not drop the product or subject it to physical shock. Keep the device away

from magnetic interference.
Power Supply
The input voltage for the device should meet the Limited Power Source (5 VDC,

2 A) according to the IEC61010-1 standard. Please refer to actual products and
technical specifications for detailed information.
Make sure the plug is properly connected to the power socket.

DO NOT connect multiple devices to one power adapter, to avoid over-heating

or fire hazards caused by overload.
T
he power source should meet limited power source or PS2 requirements

according to IEC 62368-1 standard.
Battery
The external rechargeable battery type is 18650, and the battery size should be

19 mm × 70 mm. The rated voltage is 3.6 VDC, and the battery capacity is 3200
mAh.
For long-term storage of the battery, make sure it is fully charged every half year

to ensure the battery quality. Otherwise, damage may occur.
CAUTION: Risk of explosion if the battery is replaced by an incorrect type.

Improper replacement of the battery with an incorrect type may defeat a

safeguard (for example, in the case of some lithium battery types).
Do not dispose of the battery into fire or a hot oven, or mechanically crush or

cut the battery, which may result in an explosion.
Do not leave the battery in an extremely high temperature surrounding

environment, which may result in an explosion or the leakage of flammable liquid
or gas.
Do not subject the battery to extremely low air pressure, which may result in an

explosion or the leakage of flammable liquid or gas.
Dispose of used batteries according to the instructions.

DO NOT place the battery in the reach of children.

DO NOT swallow the battery to avoid chemical burns.

Maintenance
If the product does not work properly, please contact your dealer or the nearest

service center. We shall not assume any responsibility for problems caused by
unauthorized repair or maintenance.
Wipe the device gently with a clean cloth and a small quantity of ethanol, if

necessary.
If the equipment is used in a manner not specified by the manufacturer, the

protection provided by the device may be impaired.
Clean the lens with soft and dry cloth or wiping paper to avoid scratching it.

Using Environment
Make sure the running environment meets the requirement of the device. The

operating temperature shall be -30 °C to 55 °C (-22 °F to 131 °F), and the
operating humidity shall be from 5% to 95%.
DO NOT expose the device to high electromagnetic radiation or dusty

environments.
DO NOT aim the lens at the sun or any other bright light.

Place the device in a dry and well-ventilated environment.

Avoid equipment installation on vibratory surface or places subject to shock

(neglect may cause equipment damage).
Emergency
If smoke, odor, or noise arises from the device, immediately turn off the power,
unplug the power cable, and contact the service center.
Laser
When any laser equipment is in use, make sure that the
device lens is not exposed to the laser beam, or it may burn
out. The laser radiation emitted from the device can cause
eye injuries, burning of skin or inflammable substances.
Before enabling the laser ranging function, make sure no human or
inflammable substances are in front of the laser lens. Do not place the device
where minors can fetch it. The wavelength is 905 nm, and the max. power
output is less than 1.15 mW. According to IEC 60825-1:2014 and EN 60825-
1:2014+A11:2021, this laser product is classified as Class 1 laser product.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road, Xixing Subdistrict, Binjiang
District, Hangzhou, Zhejiang 310052, China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products might be subject to export
controls in various countries or regions, including without limitation, the United
States, European Union, United Kingdom and/or other member countries of the
Wassenaar Arrangement. Please consult your professional legal or compliance
expert or local government authorities for any necessary export license
116