Hendi SPEEDOVEN X90 Manual Del Usuario página 17

Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
• Read the details in the section "Control panel".
• When the appliance is switched on, it will start the preload
process. It will take few mins to enter to the standby interface
(Fig.3 on page 5).
• The temperature indicator (30) shows the status of the cham-
ber's temperature such as heating (30a), cooling (30b) and
steady (30c) on different user interfaces.
• Install the adjustable feet before use.
Standby interface (Fig.3 on page 5)
• Select the "setting" icon (17) to enter the setting interface
(Fig.8 on page 7) .
• Select the "Click to boot" icon (16) in the middle to enter the
main interface (Fig.4a on page 5).
• When the chamber's temperature is over 70°C, Fan ON/OFF
switch" icon (15) is available. Select this icon to switch ON/
OFF the fan for cooling.
Main interface (Fig.4 on page 5)
• Date and time could be set in system setting interface (Fig.8
on page 7).
• There have 6 default categories. (19)
• You can use the searching box (20) to find the preset recipe
immediately.
• The preset recipes (24) show on the screen.
1. The appliance starts to preheating based on preheat tem-
perature. The default temperature is 260°C. You can select
the "preheat temperature" icon (22) to set the preheat tem-
perature.
2. Scroll up or down to select the recipe to enter to recipe
interface (Fig.5 on page 6). See the details in corresponding
section below. A warning – "Oven Temperature Isn't Ready,
Continue?", will be popped if the chamber's temperature
has not reached to the setting temperature. Select" " to
confirm or " " to reject.
3. Select the "quick customized" icon (21) to enter to this
quick customized interface (Fig.7 on page 7). See the de-
tails in corresponding section below.
4. You can return to the standby interface by selecting and
holding "Return to standby interface" icon (23) for 3s. The
fan will switch on automatically for cooling if the cham-
ber's temperature is over 70°C. The panel shows the actual
chamber's temperature (Fig.4b on page 5). You can choose
" " to cancel the cooling manually (not recommended).
Recipe interface (Fig.5 on page 6)
1. Cooking time, temperature, microwave power and fan
speed level are preset. There are available to be adjusted
case by case for each cooking. The adjustment will not be
saved.
NOTE: Timer and temperature could be set by entering a
value. Microwave power and fan speed level could be set by
selecting the corresponding icon separately.
2. Touch "Stage selection" icon (29) to check or adjust the
cooking parameters for different stages. The numbers of
stages are preset in setting interface. It cannot be added
in this interface.
3. Wait for the chamber's temperature until its steady.
4. When the temperature is steady, place the food in the
chamber. When the door is opened, a warning – "Door
Open", will be popped.
5. Select "start" icon (32) to start the cooking process.
6. A warning – "Does Food Load In Oven?", will be popped for
a reminder. Select " " to confirm or " " to reject.
7. The cooking process will be started and enter to the cook-
ing interface (Fig.6a on page 6). See the details in corre-
sponding section below.
Cooking interface (Fig.6a on page 6)
1. The panel shows the remaining cooking time in the middle.
2. You can select the "stop" icon (35) to stop the cooking pro-
cess. "Return" icon will be shown on the top of right corner.
Select this to go back to the recipe interface.
3. You can select "Pause/Resume" icon (33) to control the
cooking process. Under "pause" status, heating functions
are stopped but fan is still operating. No "Return" icon will
be shown.
NOTE: When the door is opened during cooking, a warning
– "Door Open", will be popped and cooking is paused. When
the door is closed again, a warning – "Cook Continue?",
will be popped. Select " " to resume cooking or " " to
stop cooking.
4. Once the cooking is finished, a message – "Cook Com-
plete", will be popped (Fig.6b on page 6).
5. If no additional time is needed, select " " to finish the
cooking.
6. If you would like to add the cooking time, manually select the
"+10" icon by 10s interval and then select " " to confirm.
NOTE: The increment interval is 10s. The additional cook-
ing time will be under the same setting of temperature,
microwave power and fan speed level.
Quick customized interface (Fig.7 on page 7)
• This is another quick option for creating a special recipe for
one time use or saving the recipe for future use.
• The interface will not change to cooking interface under
"quick customized".
1. Set the timer and temperature by entering a value.
2. Set the microwave power and fan speed level by selecting
the corresponding icon separately.
GB
17