Behringer PRO VS MINI Guia De Inicio Rapido página 9

16
PRO VS MINI
22. WAVE – Choose which waveform
is used for the currently
selected voice.
23. FREQ – Change the pitch or
frequency of the waveform.
24. RATE – Adjust the speed of
the chorus.
25. AMOUNT – Adjust the
chorus depth.
26. TEMPO – Sets the speed of the ARP
or sequencer in BPM.
27. MEMORY/WRITE – Calls up a
new sequence memory or, with
Function, writes a sequence
to internal memory.
28. FUNC – Used to engage shift mode
or for second functions.
29. PLAY/ACTIVE – Plays the
arpeggiator or selected
sequencer pattern. Function press
to make active, which allows
selected steps to be removed from
the sequence.
30. RECORD/CLEAR – Press to enter
record or function press to clear
notes or a full pattern.
31. MENU – Repeated key press gives
the following menus:
a. Seq/Arp – Switches between
normal keyboard and sequencer
operation and arpeggiator.
b. Filt Env Trig – Select either
Single or Multi trigger.
Single triggers the envelope
with the first note played and
will not re-trigger until all
notes are released; Multi will
re-trigger with each new
note played.
c. MIDI Tx – Selects MIDI output
channel 1 – 16 or off.
d. MIDI Rx – Selects MIDI input
channel 1 – 16 or off.
e. MIDI Velocity –
Switch velocity On or OFF.
f. MIDI CC – Selects whether MIDI
continuous controller messages
are received or off.
g. Prog Bulk SysEx Send –
Outputs program memory
contents as SysEx using the
USB socket.
h. Prog Sing SysEx Send –
Outputs current program as
SysEx using the USB socket.
i. Patt Bulk SysEx Send –
Outputs sequencer memory
contents as SysEx using the
USB socket.
j. Patt Sing SysEx Send –
Outputs current sequence as
SysEx using the USB socket.
k. SysEx Receive Listening
– Allows the PRO VS MINI to
receive SysEx from an external
source using the USB socket.
l. Factory Reset – Resets all
programs and sequences to
factory default. Also displays
firmware version. Press the +
button (9) or – button (10) to
initiate reset.
32. SYNC – Repeated key press gives
the following menus:
a. Sync Source – Switch between
Internal, MIDI, USB or Trigger.
b. Sync Type – Switch between
1ppq, 2ppq, 4ppq,
24ppq, 48ppq.
33. SCALE – Select 1/8, 1/8T, 1/16, 1/16T,
1/32 (global).
34. SWING – Select 50 (no swing), 55,
60, 65, 70, 75 (global).
35. ARP SET – Select up, down,
up and down.
36. SEQUENCER SET – Switch between
step fixed (note lengths defined by
step) or record (notes as recorded).
37. CLEAR ALL – Wipes all
sequencer memories.
38. CLEAR ACTIVE – Clears the
action of Active Steps (button 29)
and makes all steps active.
Quick Start Guide
39. METRONOME – Switches the
metronome on or off.
40. LFO SET – Selects the waveform for
the LFO between triangle, square,
sawtooth, ramp or S&H.
41. OSC SET – Selects coarse or fine
tuning for the oscillators using
control 23.
42. FIL ENV – Adjusts the amount of
envelope modulation of the filter
from 0 – 99.
43. MIX ENV – Repeated key press
gives the following menus:
a. Mix Env Loop – Select
between off, 0->3, 1->3, 2->3,
0<->3, 1<->3, 2<->3 (if off is
selected then no other menu
options are available).
b. Mix Env Repeat – Select
between 1 – 7 and continuous.
c. Mix Env Points: 0-4 –
Use the waveform mix control
8 to set the balance between
a, b, c and d at each point.
Move from point to point with
buttons 9 and 10.
44. NAME – Allows patch name to be
set using keyboard.
45. PROGRAM INIT – Initialises the
selected program.
17