LUND 67702 Manual De Instrucciones página 11

GB
of injury, even if the blades are not moving. Special care must be taken when handling
any accessories equipped with blades. Make sure that the selected accessory has been
installed correctly, before starting the product.Do not overload the product. The temperature
of the housing must not exceed 60 C. Overloading the product will accelerate its wear and
O
tear, lead to its damaging, and increase the risk of an electric shock. The product must be
kept under supervision at all times during operation. The product may not be used for hard
food processing, seeds, bones, shells, ligneous parts of plants. The product is not to be used
by children. Keep the product and its power cord out of the reach of children. It is important to
ensure that children do not see the product as a toy. Children should not be allowed to clean
or maintain the product without the supervision of an adult. This product cannot be used by
people with impaired physical and/or mental abilities, and by people without any experience
in or understanding of the operation of the product, unless they are supervised or instructed
in the safe use of the product, so that they understand the relevant operating risks.
PRODUCT OPERATION
Preparing the appliance for operation
Caution! All actions described in this section must be carried out with the product unplugged. Make sure that the power cord has
been unplugged from the socket.
The product must be unpacked and all parts of the packaging completely removed. It is recommended to keep the packaging, as
it can be helpful in further transporting and storing of the product.
Check the product for damage. In the event of any damage being found, do not use the product, before the damage has been
remedied or the damaged components changed for new components, free of defects.
Clean the product, according to the instructions specifi ed in the "Product Maintenance" section.
The drive base must be placed on a level, fl at, hard and stable surface. All drive housing stands should be in contact with the
ground. If the base is equipped with suction cups, make sure that they are attached to the ground. The suction cups will adhere
more easily to a smooth surface, if necessary you can slightly moisten the surface or the suction cups.
Screw the cutting base (II) to the selected accessory. Avoid contact with the blades.
Make sure that the connection is tight by turning the dishes so that the cutting base is at the bottom and then pour water into the
cup. If leaks are observed, tighten the base or screw the base again.
The mounting socket in the drive housing has an opening which, in the event of an emergency loss of tightness, should partially
drain a liquid leak under the housing. If a leak is discovered, discontinue use of the product until the cause is eliminated.
Mount the base and its accessory in the drive housing. The accessory has tabs which must be fi t into the notches in the top wall
of the drive housing (III). Next, turn the accessory clockwise.
Check that all tabs are hidden in the drive housing.
The product is equipped with an additional fuse which will prevent it from being switched on in the event of incorrect installation
of the accessory in the drive housing.
The cup is equipped with a lid which allows you to add food products while the blender is in operation. The lid is installed by placing
it on the edge of the cup and then turning it clockwise (IV). The tabs near the edge of the cup should fi t into the handles of the lid.
The lid has a small opening in the recess, which can be used to add liquid food products without removing the lid.
Using the Product
It is recommended to fi ll the cup with food when it is removed from the drive housing. This will prevent possible contamination of
the drive housing with food while the cup is being fi lled.
Do not fi ll any of the accessories above the maximum capacity marker (MAX). Consider that the food level will rise during stirring.
After fi lling, the cup should be covered with the lid.
Place the cup on the drive housing.
Make sure that the product switch is in the off position – O, then plug the power cord into the socket.
Start the product by changing the position of the switch to: 1, 2 or P.
The switch positions marked as 1 and 2 start the blender and allow you to work at one of the two speeds: 1 – slower, 2 – faster.
The P position allows the maximum operating speed to be activated as long as the switch knob is held in this position. When the
knob is released, it will automatically return to the off position – O.
The operation is stopped after changing the position of the switch to the off position – O.
Before removing the accessory, wait for the blades to stop completely, then unplug the power cord plug from the socket and
remove the accessory from the drive housing.
O R I G I N A L I N S T R U C T I O N S
11