Intended Use; Assembly And Adjustments - Black+Decker BESTA510 Manual De Instrucciones

Desbrozadora/bordeadora de cuerda
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
size to use depending on cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The
lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120 V
25 (7.6)
240 V
50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More
not
Than
More
Than
0
6
18
6
10
18
10
12
16
12
16
14
Safety Rules and Instructions:
Polarized Plug
To reduce the risk of electric shock, this equipment has
a polarized plug (one blade is wider than the other). This
equipment must be used with a suitable polarized 2 wire or
3 wire extension cord. Polarized connections will fit together
only one way. Make sure that the receptacle end of the
extension cord has large and small blade slot widths. If the
plug does not fit fully into the extension cord, reverse the
plug. If it still does not fit, obtain a suitable extension cord. If
the extension cord does not fit fully into the outlet, contact a
qualified electrician to install the proper outlet. Do not change
the tool plug or extension cord in any way.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will cause loss
of power and overheating. BLACK+DECKER tools are factory
tested; if this tool does not operate, check power supply.
4
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
American Wire gauge
16
16
16
14
16
14
12
Not Recommended
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Fig. A at the beginning of this manual for a
complete list of components.

Intended Use

This appliance is designed for residential outdoor
trimming applications.
DO nOT use under wet conditions or in presence of
flammable liquids or gases.
DO nOT let children come into contact with the tool.
14
Supervision is required when inexperienced operators use
12
this tool.
12

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.

WARNING: Unplug the trimmer before attempting
to attach the guard, EDGE GUIDE OR HANDLE. NEVER
OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE.
THE GUARD MUST ALWAYS BE ON THE TOOL TO
PROTECT THE USER.
Attaching the Guard (Fig. B, C)

WARNING: NEVER OPERATE trimmer WITHOUT
GUARD FIRMLY IN PLACE.
Turn the trimmer upside down so that you are looking
down at the spool
Remove the screw from the guard with a
phillips screwdriver.
Turn the guard
the motor housing
the guard engage the ribs
as shown in Fig. B. The locking tab
snapped into the housing slot
Continue to slide the guard on until you hear it "snap"
into place.
Insert the guard screw and tighten securely as shown in
Fig. C to complete the guard assembly.
Once the guard is installed, remove the covering from
the line cut-off blade, located on the edge of the guard.
Fig. B
26
8
9
 9 
.
 8 
upside down and slide it fully onto
 6 
. Make sure the tabs
 11 
on the motor housing
 25 
should have
 26 
.
 10 
on
25
10
11
6

Publicidad

Tabla de contenido
loading

Tabla de contenido